Criteria

Text:
Display:

Results

Viewing 1 to 30 of 16944
CURRENT
2017-09-20
Standard
AMS2550F
This specification covers the enginering requirements for a treatment to provide enhanced corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
CURRENT
2017-09-20
Standard
AMS2435H
This specification covers the engineering requirements for applying tungsten carbide/cobalt coatings to metal parts by the detonation process and the properties of such coatings. This coating has been used typically to provide a hard, wear resistant surface on metal parts which do not operate in service higher than 1000 degrees F (538 degrees C) but usage is not limited to such applications. These coatings are not recommended for surfaces with deep vee-shaped grooves, blind cavities, narrow holes or sharp corners, or where deformation of the base metal may be expected. Higher cobalt content provides increased ductility for applications where impact or fretting wear is involved.
CURRENT
2017-09-19
Standard
AMS2451/6B
This specification establishes the requirements for brush plating of copper by electrodeposition.
CURRENT
2017-09-19
Standard
AMS2690D
This specification defines the equipment, procedures, and requirements for joining leads by parallel gap resistance welding. For attaching leads by parallel gap resistance welding in the assembly of microelectronic circuitry to thin film substrates.
CURRENT
2017-09-19
Standard
AMS3079C
Protection of metal parts where a soft, readily-removable film is desired and additional protective packaging is provided.
CURRENT
2017-09-18
Standard
AMS4981H
This specification covers a titanium alloy in the form of bars, wire, and forgings up through 4.000 inches (101.60 mm), inclusive, in diameter or least distance between parallel sides and forging stock of any size (see 8.6).
CURRENT
2017-09-18
Standard
AMS5333G
This specification covers a low-alloy steel in the form of investment castings.
CURRENT
2017-09-14
Standard
AMS5337E
This specification covers an alloy steel in the form of investment castings.
CURRENT
2017-09-14
Standard
AMS5338H
This specification covers a low-alloy steel in the form of investment castings.
CURRENT
2017-09-13
Standard
AMS4466A
This specification covers an aluminum alloy in the form of alclad sheet and plate 0.020 to 0.500 inch (0.508 to 12.70 mm) inclusive, in thickness, supplied in the -T361 temper (see 8.5).
CURRENT
2017-09-13
Standard
AMS4163F
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to 2.999 inches, incl (76.17 mm, incl) in thickness, nominal diameter or wall thickness with cross-sectional area 25 in2 (161 cm2) and under (see 8.5).
CURRENT
2017-09-13
Standard
AMS5336J
This specification covers a low-alloy steel in the form of investment castings.
CURRENT
2017-09-11
Standard
AMS4251B
This specification covers an aluminum alloy in the form of sheet 0.040 to 0.249 inch (1.02 to 6.32 mm) in thickness (see 8.6).
CURRENT
2017-09-11
Standard
AMS4971L
This specification covers a titanium alloy in the form of bars, wire, forgings and flash welded rings 4.000 inches (101.60 mm) and under in diameter or least distance between parallel sides and stock for forging or flash welded rings of any size (see 8.6).
CURRENT
2017-09-05
Standard
AMS6407K
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
CURRENT
2017-09-05
Standard
AMS4892D
This specification covers a nickel-copper alloy in the form of castings.
CURRENT
2017-09-05
Standard
AMS4935L
This specification covers a titanium alloy in the form of extruded bars and shapes, flash welded rings 3.000 inches (76.20 mm) and under in nominal diameter or least distance between parallel sides, and stock for flash welded rings.
CURRENT
2017-08-30
Standard
AMS4558H
This specification covers a copper alloy (brass) in the form of seamless tubing.
CURRENT
2017-08-29
Standard
AMS6430J
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings.
CURRENT
2017-08-29
Standard
AMS4979J
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings 4.000 inches (101.60 mm) and under in nominal diameter or least distance between parallel sides and stock of any size for forging or flash welded rings.
CURRENT
2017-08-29
Standard
AMS4941G
This specification covers one grade of commercially pure titanium in the form of welded tubing.
CURRENT
2017-08-28
Standard
AMS3793C
This specification and its supplementary detail specifications cover para aramid in the form of tape and webbing.
CURRENT
2017-08-25
Standard
AMS4893D
This specification covers a nickel-copper alloy in the form of castings.
CURRENT
2017-08-24
Standard
AMS6317K
This specification covers an aircraft-quality, low-alloy steel in the form of heat treated bars and forgings.
CURRENT
2017-08-22
Standard
AMS4275E
This specification covers an aluminum alloy in the form of permanent mold castings.
CURRENT
2017-08-22
Standard
AMS6280M
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, flash welded rings, and stock for forging or flash welded rings.
CURRENT
2017-08-22
Standard
AMS6424G
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
CURRENT
2017-08-17
Standard
AMS3793/3C
This specification covers three classes of para-aramid tape and webbing of a single width and with varying weights.
CURRENT
2017-08-17
Standard
AMS4553D
This specification covers a copper alloy (brass) in the form of seamless tubing with nominal OD of 0.405 inch (10.29 mm) to 10.75 inches (273.05 mm) and nominal weight of 0.253 lb/ft (0.38 kg/m) to 2.176 lb/ft (3.24 kg/m) (see 8.6).
CURRENT
2017-08-17
Standard
AMS7464D
This specification covers premium quality bolts and screws made from a low-alloy, heat-resistant steel and having threads of UNJ (MIL-S-8879) form.
Viewing 1 to 30 of 16944

Filter

  • Range:
    to:
  • Year: