Criteria

Text:
Display:

Results

Viewing 331 to 360 of 17074
CURRENT
2017-03-02
Standard
AMS3593B
This specification covers an irradiated, thermally-stabilized, flame-resistant, modified-polyvinylidene-fluoride plastic in the form of extra-thin-wall tubing.
CURRENT
2017-03-01
Standard
AMS1428J
This foundation specification (AMS1428J) and its associated category specifications (AMS1428/1 and AMS1428/2) cover three types of deicing/anti-icing fluids, each in the form of a non-Newtonian fluid.
CURRENT
2017-03-01
Standard
AMS3582B
This specification covers a crosslinked polyvinyl chloride plastic in the form of flexible, thin-wall, heat-shrinkable tubing.
CURRENT
2017-03-01
Standard
AMS5916B
This specification covers a corrosion and heat-resistant alloy in the form of sheet, strip, and plate 2.00 inch (50.8 mm) and under in thickness (see 8.4).
CURRENT
2017-03-01
Standard
AMS6509A
This specification covers a premium aircraft-quality alloy steel in the form of bars 199 in2 (1284 cm2) and under in cross section, forgings, and forging stock.
CURRENT
2017-02-28
Standard
AMS3683B
This specification covers a thermally-stabilized, irradiated, modified fluoropolymer in the form of very-thin-wall tubing.
CURRENT
2017-02-27
Standard
AMS2451/14
This specification covers the requirements for brush plating of nickel-tungsten by electrodeposition.
CURRENT
2017-02-23
Standard
AMS3266A
This specification covers two types of electrically conductive, elastomeric polythioether sealing compounds that cure at room temperature. The sealing compound is supplied as either a two-component system or as premixed and frozen.
CURRENT
2017-02-23
Standard
AMS3217/4C
This specification covers a standard fluoroelastomer (FKM) rubber stock in the form of molded test slabs.
HISTORICAL
2017-02-22
Standard
AMS4959F
This specification covers a titanium alloy in the form of cold drawn wire.
CURRENT
2017-02-22
Standard
AMS3102
This specification covers a fuel-resistant polythioether sealing compound with low specific gravity, supplied as a two-component system which cures at room temperature.
CURRENT
2017-02-21
Standard
AMS4290M
This specification covers an aluminum alloy in the form of die castings.
CURRENT
2017-02-17
Standard
AMSQQA225/4A
This specification covers the specific requirements for 2014 aluminum alloy bar, rod, wire and special shapes produced by rolling, drawing or cold finishing.
CURRENT
2017-02-15
Standard
AMS5047G
This specification covers an aluminum-killed carbon steel in the form of sheet and strip.
CURRENT
2017-02-14
Standard
AMS4071N
This specification covers an aluminum alloy in the form of drawn, round seamless tubing having a wall thickness of 0.010 to 0.450 inch (0.25 to 11.43 mm) inclusive, and nominal outside diameters of 0.125 to 3.000 inch (3.18 to 76.2 mm), inclusive (see 8.5).
CURRENT
2017-02-14
Standard
AMS1428/1
The foundation specification (AMS1428J) and the category specifications (AMS1428/1 and AMS1428/2) cover deicing/anti-icing materials in the form of a fluid.
CURRENT
2017-02-13
Standard
AMS4472A
This specification covers an aluminum alloy in the form of plate 0.500 to 2.250 inch (12.70 to 57.15 mm) in nominal thickness (see 8.5).
CURRENT
2017-02-10
Standard
AMSSTD595A
This standard defines a color index system used by, but not limited to, Government activities in a format suitable for color identification, color selection, color matching, and quality control inspection. It also describes the designation and use of color media that is available to conduct these activities. Use of the color index referenced in this standard is intended to promote standardization and consistency in the color of items produced for Government use. Color media is described as follows: Color Chip Representation, Fan Deck: Suitable for color identification and selection. Color Chip Representation, Color Book: Suitable for color identification and selection. Precise Color Matching, Individual Color Chips: Suitable for color matching and quality control inspection purposes. Precise Color Matching, Set of Color Chips: Suitable for color matching and quality control inspection purposes.
CURRENT
2017-02-09
Standard
AMS4575F
This specification covers a corrosion-resistant nickel-copper alloy in the form of copper-furnace-brazed tubing.
CURRENT
2017-02-09
Standard
AMS1428/2
The foundation specification (AMS1428J) and the category specifications (AMS1428/1 and AMS1428/2) cover deicing/anti-icing materials in the form of a fluid.
CURRENT
2017-02-09
Standard
AMS2800E
This specification covers the requirements for identification of finished parts.
CURRENT
2017-02-08
Standard
AMS2629E
This specification covers a mixture of liquid hydrocarbons and soluble additives.
CURRENT
2017-02-07
Standard
AMS2503G
This specification covers the engineering requirements for finishing aircraft parts and assemblies with a black enamel.
CURRENT
2017-02-06
Standard
AMS3579E
This specification covers a non-crosslinked polyvinyl chloride plastic in the form of flexible, thinwall, heat-shrinkable tubing with a low recovery temperature.
CURRENT
2017-02-01
Standard
AMS5647K
This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings.
CURRENT
2017-01-19
Standard
AMS5639J
This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings.
CURRENT
2017-01-18
Standard
AMS5618J
This specification covers a premium aircraft-quality corrosion-resistant steel in the form of bars, wire, forgings, and forging stock.
CURRENT
2017-01-18
Standard
AMS3400
This specification covers a polyalphaolefin/ester-blend fluid.
CURRENT
2017-01-18
Standard
AMS6431P
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
CURRENT
2017-01-12
Standard
AMS3415E
This specification covers the requirements for an aluminum brazing flux in granular form.
Viewing 331 to 360 of 17074

Filter

  • Range:
    to:
  • Year: