Criteria

Text:
Display:

Results

Viewing 61 to 90 of 17015
CURRENT
2017-10-04
Standard
AMS03_19A
This SAE Standard specifies the requirements for the electro-deposition of cadmium on non-corrosion resisting steel items for protection against corrosion, and on copper based alloy items and corrosion resisting steel items for the reduction of contact corrosion of less noble metallic materials.
CURRENT
2017-10-04
Standard
AMS03_25A
This SAE Standard specifies the properties of sulphuric acid anodizing of aluminum and aluminum alloys.
CURRENT
2017-10-03
Standard
AMS6320P
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, flash welded rings, and stock for forging or flash welded rings.
CURRENT
2017-09-29
Standard
AMS6323M
This specification covers an aircraft-quality, low-alloy steel in the form of mechanical tubing.
CURRENT
2017-09-29
Standard
AMS2647F
This specification details requirements and procedures for the detection of defects in aircraft and engine components during maintenance and overhaul operations.
CURRENT
2017-09-27
Standard
AMS6450K
This specification covers a low-alloy steel in the form of wire supplied as coils, spools, and straight lengths.
CURRENT
2017-09-22
Standard
AMSM7866B
This specification covers the requirements for procurement of one grade of powdered molybendum disulfide to be used in lubricants and greases for surfaces where boundary conditions exist.
CURRENT
2017-09-22
Standard
AMS6327L
This specification covers an aircraft-quality, low-alloy steel in the form of bars and forgings.
CURRENT
2017-09-22
Standard
AMS2685F
This specification defines the requirements for joining metals and alloys using the gas-tungsten-arc welding (GTAW) methods.
CURRENT
2017-09-20
Standard
AMS2510F
This specification covers the engineering requirements for finishing aircraft parts and assemblies with an engine gray enamel.
CURRENT
2017-09-20
Standard
AMS2550F
This specification covers the engineering requirements for a treatment to provide enhanced corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic Corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
CURRENT
2017-09-20
Standard
AMSM45202B
This specification covers the requirements for equipment, materials and procedures to be used in anodic treatments for magnesium base alloys for the purpose of increasing their corrosion resistance or producing surfaces suitable for the application of a protective organic finish.
CURRENT
2017-09-20
Standard
AMS2435H
This specification covers the engineering requirements for applying tungsten carbide/cobalt coatings to metal parts by the detonation process and the properties of such coatings.
CURRENT
2017-09-19
Standard
AMS2690D
This specification defines the equipment, procedures, and requirements for joining leads by parallel gap resistance welding.
CURRENT
2017-09-19
Standard
AMS2451/6B
This specification establishes the requirements for brush plating of copper by electrodeposition.
CURRENT
2017-09-18
Standard
AMS5333G
This specification covers a low-alloy steel in the form of investment castings.
CURRENT
2017-09-18
Standard
AMS4981H
This specification covers a titanium alloy in the form of bars, wire, and forgings up through 4.000 inches (101.60 mm), inclusive, in diameter or least distance between parallel sides and forging stock of any size (see 8.6).
CURRENT
2017-09-14
Standard
AMS5337E
This specification covers an alloy steel in the form of investment castings.
CURRENT
2017-09-14
Standard
AMS5338H
This specification covers a low-alloy steel in the form of investment castings.
CURRENT
2017-09-13
Standard
AMS4466A
This specification covers an aluminum alloy in the form of alclad sheet and plate 0.020 to 0.500 inch (0.508 to 12.70 mm) inclusive, in thickness, supplied in the -T361 temper (see 8.5).
CURRENT
2017-09-13
Standard
AMS4163F
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to 2.999 inches, incl (76.17 mm, incl) in thickness, nominal diameter or wall thickness with cross-sectional area 25 in2 (161 cm2) and under (see 8.5).
CURRENT
2017-09-13
Standard
AMS5336J
This specification covers a low-alloy steel in the form of investment castings.
CURRENT
2017-09-11
Standard
AMS4251B
This specification covers an aluminum alloy in the form of sheet 0.040 to 0.249 inch (1.02 to 6.32 mm) in thickness (see 8.6).
CURRENT
2017-09-11
Standard
AMS4971L
This specification covers a titanium alloy in the form of bars, wire, forgings and flash welded rings 4.000 inches (101.60 mm) and under in diameter or least distance between parallel sides and stock for forging or flash welded rings of any size (see 8.6).
CURRENT
2017-09-05
Standard
AMS4892D
This specification covers a nickel-copper alloy in the form of castings.
CURRENT
2017-09-05
Standard
AMS4935L
This specification covers a titanium alloy in the form of extruded bars and shapes, flash welded rings 3.000 inches (76.20 mm) and under in nominal diameter or least distance between parallel sides, and stock for flash welded rings.
CURRENT
2017-09-05
Standard
AMS6407K
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
CURRENT
2017-08-30
Standard
AMS4558H
This specification covers a copper alloy (brass) in the form of seamless tubing.
CURRENT
2017-08-29
Standard
AMS6430J
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings.
Viewing 61 to 90 of 17015

Filter

  • Range:
    to:
  • Year: