Refine Your Search

Topic

Search Results

Standard

Nickel Alloy, Corrosion and Heat Resistant, Forgings 57Ni 19.5Cr 13.5Co 4.3Mo 3.0Ti 1.4Al 0.05Zr 0.006B, Consumable Electrode or Vacuum Induction Melted, 1825 to 1900°F (996 to 1038°C) Solution, Stabilization, and Precipitation Heat Treated

1982-01-01
HISTORICAL
AMS5704C
This specification covers a corrosion and heat resistant nickel alloy in the form of forgings and forging stock. These forgings have been used typically for rotating parts, such as compressor blades, discs, hubs, shafts, and spacers requiring high strength up to 1500 degrees F (816 degrees C) and oxidation resistance up to 1750 degrees F (954 degrees C), but usage is not limited to such applications.
Standard

Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings and Rings, 74Ni - 7.0Cr - 16.5Mo, Solution Heat Treated

1982-01-01
HISTORICAL
AMS5771B
This specification covers a corrosion and heat-resistant nickel alloy in the form of bars, forgings, flash welded rings, and stock for forging or flash welded rings. These products have been used typically for parts, such as turbine air-sealing components, requiring moderate strength up to 1400 °F (760 °C) and oxidation resistance up to 1600 °F (871 °C), particularly where a low coefficient of expansion is desirable, but usage is not limited to such applications.
Standard

Titanium Alloy, Sheet, Strip, and Plate, 6.0Al - 4.0V, Extra Low Interstitial, Annealed

1982-01-01
HISTORICAL
AMS4907D
This specification covers a titanium alloy in the form of sheet, strip, and plate. These products have been used typically for parts requiring a combination of weldability, ductility, and good notch-toughness down to –423 °F (–253 °C), but usage is not limited to such applications. Certain processing procedures and service conditions may cause these products to become subject to stress corrosion cracking; ARP982 recommends practices to minimize such conditions.
Standard

Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 57Ni 19.5Cr 13.5Co 4.3Mo 3.0Ti 1.4Al 0.006B 0.05Zr Consumable Electrode or Vacuum Induction Melted 1825 to 1900°F Solution Heat Treated

1982-01-01
HISTORICAL
AMS5706F
This specification covers a corrosion and heat resistant nickel alloy in the form of bars, forgings, flash welded rings, and stock for forging, flash welded rings, or heading procured in inch/pound units. MAM 5706 is the metric version of this AMS. These products have been used typically for parts, such as fasteners, flanges, and rings, requiring high strength up to 1500 degrees F and oxidation resistance up to 1750 degrees F, particularly those parts which are formed or welded and then heat treated to develop required properties, but usage is not limited to such applications.
Standard

Shot Peening, Automatic

1982-01-01
HISTORICAL
AMS2430J
This specification covers the engineering requirements for automatic peening of surfaces of parts by impingement of metallic shot, glass beads, or ceramic shot. To induce residual compressive stress in surface layers of parts, thereby increasing fatigue strength and resistance to stress-corrosion cracking but usage is not limited to such applications.
Standard

Chloroprene (Cr) Rubber, Weather Resistant, 75-85

1982-01-01
HISTORICAL
AMS3242E
This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically for parts, such as window channels, bumper pads, chafing strips, and seals, requiring resistance to weather and for use from -40 to +100 °C (-40 to +212 °F), but usage is not limited to such applications.
X