Refine Your Search

Topic

Search Results

Standard

Tolerances, Metric, Nickel, Nickel Alloy, and Cobalt Alloy Sheet, Strip, and Plate

1981-10-01
HISTORICAL
MAM2262
This specification covers established manufacturing tolerances applicable to sheet, strip, and plate of nickel, nickel alloys, and cobalt alloys ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. The term 'excl' is used to apply only to the higher figure of a specified range.
Standard

Steel Bars, 1.0Cr - 0.20Mo - 0.045Se (0.39 - 0.48C) (4142H Modified), Die-Drawn, 130 ksi (896 MPa) Yield Strength, Free Machining

1981-10-01
HISTORICAL
AMS6378B
This specification covers a free-machining, low-alloy steel in the form of round bars 3.50 inches (88.9 mm) and under in nominal diameter. These bars have been used typically for parts, such as shafts, axles, pins, fasteners, gears, and screw machine parts, which are normally used at hardness of 30 to 36 HRC and which do not require a high degree of ductility, but usage is not limited to such applications.
Standard

Tolerances, Nickel, Nickel Alloy, and Cobalt Alloy Sheet, Strip and Plate

1981-10-01
HISTORICAL
AMS2262D
This specification covers established manufacturing tolerances applicable to sheet, strip, and plate of nickel, nickel alloys, and cobalt alloys ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" is used to apply only to the higher figure of a specified range.
Standard

Steel, Corrosion Resistant, Bars and Wire, 18Cr - 9.0Ni (SAE 30302), Solution Heat Treated and Cold Drawn, 125 ksi (862 MPa) Tensile Strength

1981-10-01
HISTORICAL
AMS5637D
This specification covers a corrosion-resistant steel in the form of bars and wire 0.75 inch (19 mm) and under in nominal diameter or distance between parallel sides. These products have been used typically for small parts, such as bolts, screws, and clevis pins, requiring corrosion resistance up to 700 degrees F (371 degrees C) and which may be fabricated by heading or by machining from bars or wire and roll threading, but usage is not limited to such applications.
Standard

Nickel Alloy, Corrosion and Heat Resistant, Sheet and Strip 73Ni - 15.5Cr - 2.4Ti - 0.7Al - 7.0Fe Annealed

1981-10-01
HISTORICAL
AMS5541C
This specification covers a corrosion and heat resistant nickel alloy in the form of sheet and strip. These products have been used typically for parts requiring high strength up to 1500 degrees F (816 degrees C) and oxidation resistance up to 1800 degrees F (982 degrees C), but usage is not limited to such applications. Parts may be formed and then heat treated to improve strength at elevated temperatures.
Standard

Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 58Ni 19.5Cr 13.5Co 4.3Mo 3.0Ti 1.4Al Consumable Electrode or Vacuum Induction Melted 1975°F (1079°C) Solution Heat Treated

1981-10-01
HISTORICAL
AMS5708E
This specification covers a corrosion and heat resistant nickel alloy in the form of bars, forgings, flash welded rings, and stock for forging, flash welded rings, or heading. These products have been used typically for parts, such as bolts and turbine blades, requiring high strength up to 1500 degrees F (816 degrees C) and oxidation resistance up to 1750 degrees F (954 degrees C), but usage is not limited to such applications.
Standard

COATING OF FASTENERS Aluminum Filled, Ceramic Bonded Coating

1981-07-01
HISTORICAL
AMS2506B
This specification covers the procedure for application to fasteners of a corrosion and heat resistant aluminum coating material having a thermosetting inorganic binder and the properties of the finished coating.
Standard

RADIOGRAPHIC INSPECTION

1981-07-01
HISTORICAL
AMS2635C
This specification covers the procedures for radiographic inspection.
X