Criteria

Text:
Display:

Results

Viewing 241 to 270 of 17015
CURRENT
2017-04-04
Standard
AMS4949B
This specification covers titanium in the form of laminated sheet.
CURRENT
2017-04-04
Standard
AMS6481D
This specification covers a nitriding grade of premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
CURRENT
2017-04-04
Standard
AMSSTD753B
This standard describes general and detailed methods of sampling and testing for surface passivity of corrosion-resistant steel parts. These tests may also be useful to determine if there is a need for passivation.
CURRENT
2017-04-03
Standard
AMS5623D
This specification covers a high-expansion steel in the form of bars, forgings, and forging stock.
CURRENT
2017-04-03
Standard
AMS5683G
This specification covers a corrosion and heat resistant nickel alloy in the form of welding wire.
CURRENT
2017-04-03
Standard
AMS5691H
This specification covers a corrosion and heat resistant steel in the form of covered welding electrodes. Primarily for shielded-metal-arc welding of parts fabricated from steels of similar composition, particularly when the weld zone is required to have strength and corrosion-resistance comparable to those of the parent metal.
CURRENT
2017-04-03
Standard
AMS5550F
This specification covers a corrosion and heat resistant nickel alloy in the form of sheet and strip.
CURRENT
2017-04-03
Standard
AMS4617A
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, shapes, and tubing 0.040 to 4.499 inches (1.01 to 114.27 mm) inclusive, in nominal diameter or least thickness, and with areas up to 32 in2 (206 cm2), inclusive (see 8.5).
CURRENT
2017-03-31
Standard
AMS3023B
This specification covers a trimethylol propane triheptanoate fluid (see 8.2) representative of standard type (SPC) gas turbine engine oils.
CURRENT
2017-03-30
Standard
AMS3197M
This specification covers a chloroprene (CR) rubber sponge in the form of sheet, strip, molded shapes, or other forms, as ordered.
CURRENT
2017-03-30
Standard
AMS4933F
This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, and flash welded rings up through 4.000 in2 (25.81 cm2) cross-section and stock for flash welded rings.
CURRENT
2017-03-30
Standard
AMS4261G
This specification covers an aluminum alloy in the form of investment castings.
CURRENT
2017-03-28
Standard
AMS4959G
This specification covers a titanium alloy in the form of cold drawn wire.
CURRENT
2017-03-28
Standard
AMS4939C
This specification covers a titanium alloy in the form of sheet, strip, and plate through 4.000 inches (101.60 mm) nominal thickness.
CURRENT
2017-03-28
Standard
AMS2808E
This specification covers the requirements for identification of forgings, including die forgings, hand forgings, and rolled rings.
CURRENT
2017-03-28
Standard
AMS4782G
This specification covers a nickel alloy in the form of wire, rod, strip, foil, and powder and a viscous mixture (paste) of the powder in a suitable binder.
CURRENT
2017-03-24
Standard
AMS5339G
This specification covers an alloy steel in the form of investment castings.
CURRENT
2017-03-24
Standard
AMS5085J
This specification covers a carbon steel in the form of sheet, strip, and plate.
CURRENT
2017-03-23
Standard
AMS4284K
This specification covers an aluminum alloy in the form of permanent mold castings.
CURRENT
2017-03-23
Standard
AMS5824F
This specification covers a corrosion-resistant steel in the form of welding wire.
CURRENT
2017-03-21
Standard
AMS03_1A
This SAE Standard specifies the processes and type of impregnant which can be used when impregnating castings for the following purposes: a. For the recovery of ferrous and non-ferrous castings containing micro porosity, where pressure tightness is mandatory. b. For sealing castings/sinter metal components to improve corrosion resistance and/or to render the surface suitable for subsequent surface treatment.
CURRENT
2017-03-21
Standard
AMS03_3A
This SAE Standard specifies the requirements for the application of sprayed metal coatings of aluminum, zinc, or aluminum-zinc based alloys for the protection of aluminum alloys against corrosion. It does not cover the metal spraying of aluminum armour materials, which should be treated in accordance with the requirements of Def Stan 08-39.
CURRENT
2017-03-21
Standard
AMS03_040A
This SAE Standard specifies the guidance and the requirements for the electrodeposition of zinc-nickel alloy coatings on a range of metallic substrates for the provision of corrosion resistance to steel components and galvanic compatibility between some bi-metallic contacting surfaces.
CURRENT
2017-03-21
Standard
AMS03_2A
This SAE Standard specifies processes for the cleaning of metal surfaces to remove any extraneous or undesirable material or deposits at any stage of manufacture, storage or service and for the preparation of these surfaces for further treatment. Any necessary stress-relieving treatments are also included. This Standard does not override special preparatory procedures specified in individual Defence Standards, Defence Specifications, DTD Process Specifications, DG Ships Specifications and Naval Defence Standards. It also does not cover cleaning operations associated with the maintenance of internal combustion engines, the preliminary removal of heavy deposits of oil, grease, or dirt accumulated during operational service, preparations for welding and the cleaning of electrical contacts.
CURRENT
2017-03-21
Standard
AMS03_4A
This SAE Standard specifies the special treatments and precautions that are to be observed when protective and other surface treatments are applied to items, including springs, made from steel of specified maximum tensile strength exceeding 1450 MPa. The requirements of this Standard qualify those in process specifications and override the latter where there is conflict. The Standard also gives advice on design, manufacture, and preparation of items prior to cleaning and protection.
CURRENT
2017-03-17
Standard
AMS2451/4C
This specification establishes the requirements for brush plating of cadmium by electrodeposition.
CURRENT
2017-03-14
Standard
AMS4079H
This specification covers an aluminum alloy in the form of drawn, round, seamless tubing with wall thickness of 0.018 to 0.500 inch (0.46 to 12.70 mm), inclusive (see 8.5).
CURRENT
2017-03-08
Standard
AMS2418J
This specification covers the requirements for electrodeposited copper.
CURRENT
2017-03-07
Standard
AMS4473A
This specification covers an aluminum alloy in the form of plate 0.750 to 1.500 inch (19.05 to 38.10 mm), inclusive, in nominal thickness.
CURRENT
2017-03-03
Standard
AMS2368D
This specification provides a standard set of procedures for sampling and testing to meet the requirements of material specifications for wrought titanium and titanium alloy products, except forgings and forging stock. It is applicable to the extent specified in a material specification.
Viewing 241 to 270 of 17015

Filter

  • Range:
    to:
  • Year: