Refine Your Search

Topic

Search Results

Standard

Grease, Aircraft, General Purpose, Low Temperature Range, Lithium Thickened

2018-05-16
CURRENT
AMS3052A
This specification covers grease for use within an aircraft. It also defines the quality control requirements to assure batch conformance and materials traceability, and the procedures to manage and communicate changes in the grease formulation and brand. This specification invokes the Performance Review Institute (PRI) product qualification process. Requests for submittal information may be made to the PRI at the address in 2.2, referencing this specification. Products qualified to this specification are listed on a Qualified Products List (QPL) managed by the PRI. Additional tests and evaluations may be required by individual equipment builders before a grease is approved for use in their equipment. Approval and/or certification for use of a specific grease in aero and aero-derived marine and industrial applications is the responsibility of the individual equipment builder and/or governmental authorities and is not implied by compliance with or qualification to this specification.
Standard

Elastomer: Silicone Rubber (MQ/VMQ) General Purpose 35 – 45 Durometer Type ‘A’ Hardness

2018-05-16
CURRENT
AMS3301J
This specification covers a silicone (MQ/VMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, O-ring cord, and molded in place gaskets for aeronautical and aerospace applications without complete consideration of the end use prior to the selection of this material.
Standard

Fluorosilicone Rubber (FVMQ) Fuel and Oil Resistant 55 – 65 Durometer Type ‘A’ Hardness For Products in Fuel Systems / Lubrication Oils

2018-05-16
CURRENT
AMS3325G
This specification covers a fluorosilicone (FVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, O-ring cord, and molded in place gaskets for aeronautical and aerospace applications without complete consideration of the end use prior to the selection of this material.
Standard

Shim Stock, Laminated

2018-05-07
CURRENT
AMSDTL22499B
This specification covers the requirements for surface bonded laminated shim stock.
Standard

Peening Media General Requirements

2018-05-07
CURRENT
AMS2431D
This specification and its detail slash specifications cover the requirements for media to be used in controlled shot peening of metal parts.
Standard

Heat Treatment of Carbon and Low-Alloy Steel Parts Minimum Tensile Strength Below 220 ksi (1517 MPa)

2018-04-28
CURRENT
AMS2759/1F
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of carbon and low-alloy steel parts to minimum ultimate tensile strengths below 220 ksi (1517 MPa). Parts are defined in AMS2759. Due to limited hardenability in these materials, there are size limits in this specification.
Standard

Heat Treatment of Low-Alloy Steel Parts Minimum Tensile Strength 220 ksi (1517 MPa) and Higher

2018-04-28
HISTORICAL
AMS2759/2G
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of low-alloy steel parts to minimum ultimate tensile strengths of 220 ksi (1517 MPa) and higher. Parts are defined in AMS2759. The requirements for heat treatment of alloy Aermet100 are no longer part of this specification and can be found in AMS2759/3. Due to the limited hardenability of these materials, size limits have been added to this specification.
Standard

Heat Treatment Austenitic Corrosion-Resistant Steel Parts

2018-04-28
CURRENT
AMS2759/4D
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for annealing of austenitic corrosion-resistant steel parts. Parts are defined in AMS2759. General ordering instructions are specified in AMS2759.
Standard

Heat Treatment of Steel Parts General Requirements

2018-04-28
CURRENT
AMS2759F
This specification establishes general requirements for the processes listed in 3.8.1 for heat treatment of steel parts (see 8.2.1) by users or their vendors or subcontractors.
Standard

Heat Treatment Martensitic Corrosion-Resistant Steel Parts

2018-04-28
CURRENT
AMS2759/5E
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of martensitic corrosion-resistant steel parts. Parts are defined in AMS2759. General ordering instructions are specified in AMS2759.
Standard

Stress Relief of Steel Parts

2018-04-28
CURRENT
AMS2759/11A
This specification, in conjunction with the general requirements for steel heat treatment in AMS2759, establishes requirements for thermal stress relief treatments of parts manufactured from the following materials: a Carbon and low alloy steels b Tool steels c Precipitation hardening, corrosion resistant and maraging steels d Austenitic corrosion resistant steels e Martensitic corrosion resistant steels
Standard

Heat Treatment Precipitation-Hardening Corrosion-Resistant, Maraging, and Secondary Hardening Steel Parts

2018-04-28
CURRENT
AMS2759/3G
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of precipitation-hardening corrosion-resistant, maraging and secondary hardening, steel parts. Parts are defined in AMS2759. Parts made from steels other than those specified in this specification may be heat treated in accordance with the applicable requirements herein using processing temperatures, times, and other parameters recommended by the material producer unless otherwise specified by the purchaser. General ordering instructions are specified in AMS2759.
X