Criteria

Text:
Display:

Results

Viewing 121 to 150 of 13318
CURRENT
2017-09-05
Standard
AS85028C
This specification covers environment and fluid resisting, rectangular type, rack to panel electrical connectors (plugs and receptacles). These connectors utilize individually sealing removable crimp type contacts and are capable of continuous operation from −65 to +150 °C.
CURRENT
2017-09-05
Standard
AS5242C
CURRENT
2017-09-05
Standard
ARP4014A
This SAE Aerospace Recommended Practice (ARP) describes a method of conducting an endurance test using contaminated air when the applicable specification requires non-recirculation of the contaminants. The objective of the test is to determine the resistance of the engine mounted components to wear or damage caused by the contaminated air. The method described herein calls for non-recirculation of the contaminants and is intended to provide a uniform distribution of the contaminant at the inlet to the Unit Under Test (UUT). The UUT may require the use of a hydraulic fluid for actuation of components within the test unit. Contamination of the test hydraulic fluid is not part of this recommended practice. If contaminated hydraulic fluid is required by the applicable test specification, refer to MAP749.
CURRENT
2017-09-05
Standard
AS7477G
This document covers bolts and screws made from a corrosion and heat resistant, precipitation hardenable iron base alloy of the type identified under the Unified Numbering System as UNS S66286.
CURRENT
2017-09-05
Standard
AS13001A
This standard establishes the common requirements for training of DPRV personnel for use at all levels of the aerospace engine supply chain. This standard shall apply when an organization elects to delegate product release verification by contractual flow down to its suppliers (reference 9100 and 9110 standards) and to perform product acceptance on its behalf. It is intended that organizations specify their DPRV requirements through the application of AS9117. While the delegating organization will use the AS13001 standard as the baseline for establishing DPRV process and product training, it may include additional contractual training requirements to meet its specific needs. The DPRV training material was primarily developed for aerospace engine supply chain requirements. However, this standard may also be used in other aerospace industry sectors where a DPRV process requiring specific training can be of benefit.
CURRENT
2017-08-31
Standard
ARP1616B
This document defines design, performance, and test criteria for self-sealing breakaway valves for use in crash-resistant aircraft fuel systems.
CURRENT
2017-08-31
Standard
AS25042D
CURRENT
2017-08-30
Standard
AS5188C
CURRENT
2017-08-29
Standard
AS81306A
This specification covers tools used to install tiedown straps on wire bundles and for installing connector accessory shield termination bands (see 6.1).
CURRENT
2017-08-29
Standard
AS6332
This document establishes the general requirements for the quality management of aircraft ground deicing/anti-icing systems and processes. It covers the areas of: Quality system, documentation and control of records; Management responsibility; Resource management; Product realization; and Measurement, analysis and improvement. This document defines these areas and their key aspects so they can be practically managed, and that deicing operations can become safer with time. In alignment with AS6285 and AS6286, the primary focus of this standard is on the deicing/anti-icing of aircraft using deicing and anti-icing fluids.
CURRENT
2017-08-28
Standard
AS13004
This standard defines requirements for the identification, assessment, mitigation, and prevention of risk in the manufacturing process through the application of Process Flow Diagrams (PFDs), Process Failure Mode and Effects Analysis (PFMEA) and Control Plans throughout the life cycle of a product. This standard aligns and collaborates with the requirements of AS9100, AS9102, AS9103, and AS9145. The requirements specified in this standard apply in conjunction with and are not alternative to contractual and applicable statutory and regulatory requirements. In case of conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence.
CURRENT
2017-08-24
Standard
AS8017D
This SAE Aerospace Standard (AS) establishes minimum performance standards for new equipment anticollision light systems. This Aerospace Standard defines minimum light intensity in terms of "effective intensity" as defined in paragraph 3.5 of this standard and specified vertical and horizontal directions about the longitudinal and vertical axis of the airplane. It will also define flash rate and color for the anticollision light system. It is not intended that this standard require the use of any particular light source such as Xenon, LED or any other specific design of lamp.
CURRENT
2017-08-24
Standard
ARP4168B
This ARP covers three common light sources, incandescent, electroluminescent and light emitting diode that, when NVG filtered, can be used to illuminate NVG compatible aerospace crew stations. It is recognized that many other different light sources can also be used for this purpose. Also see 2.1.1 for other SAE documents that cover particular applications within the crew station environment. This ARP sets forth recommendations for the design of NVG compatible lighting, utilizing these light sources, that will meet the requirements of MIL-L-85762 Lighting, Aircraft, Interior, Night Vision Imaging System (NVIS) Compatible. This also includes the replacement document MIL-STD-3009: Lighting, Aircraft, Night Vision Imaging System (NVIS) Compatible. Although this ARP concentrates on lamp light sources for illumination, the information contained within this ARP may be directly applied to incandescent, electroluminescent and light emitting diode information display devices.
CURRENT
2017-08-24
Standard
ARP4822A
This SAE Aerospace Recommended Practice (ARP) reviews the basics of NVIS compatibility and discusses the specific illuminated pushbutton switch and indicator requirements for sunlight readability, color, luminance, and NVIS radiance when used in NVIS compatible cockpits. The recommendations and special considerations set forth in this document are made to give the design engineer a better understanding of MIL-L-85762A and MIL-STD-3009 NVIS compatibility requirements and to provide information on the visual characteristics of NVIS compatible pushbutton switch and indicators. The recommendations are primarly for military aircraft since civilian aircraft FAR requirements typically do not cover NVIS applications with the exception of those covered by RTCA/DO-275.
CURRENT
2017-08-24
Standard
AS21919A
CURRENT
2017-08-22
Standard
AS4668C
Viewing 121 to 150 of 13318

Filter

  • Range:
    to:
  • Year: