Criteria

Text:
Sector:
Content:
Display:

Results

Viewing 421 to 450 of 35602
CURRENT
2017-09-25
Standard
AS100026B
2017-09-25
WIP Standard
AMS2807C
This specification covers procedures for identifying carbon and low-alloy steels, corrosion and heat-resistant steels and alloys, maraging and other highly-alloyed steels, and iron alloy sheet, strip, and plate, and aircraft tubing.
2017-09-24
WIP Standard
ARP5584A
This SAE Aerospace Recommended Practices (ARP) covers the definitions, functions and broad application guidelines of modern aerospace vehicle electric power management systems. As aerospace control systems have become more sophisticated and autonomous, the electric power subsystem no longer is just a generation and distribution bus control system. New electric power systems include integration of individual load logic control, protection, generation, distribution, and load management. This system can report to a higher level control system, typically a vehicle management system, or can be an autonomous system within itself reporting and responding to operator commands.
2017-09-23
WIP Standard
AMS2253F
This specification covers established inch/pound manufacturing tolerances applicable to carbon and alloy tubing ordered to inch/pound dimensions. These tolerances apply to all conditions unless otherwise noted. The term 'excl' is used to apply only to the higher figure of the specified range.
2017-09-23
WIP Standard
AMS6352L
This specification covers an aircraft quality, low alloy steel in the form of sheet, strip, and plate. These products have been used typically for heat treated parts and structures that may require welding during fabrication, but usage is not limited to such applications. It may be through-hardened to a minimum tensile strength of 180 ksi (1241 MPa) in sections 0.125 inch (3.18 mm) and under in nominal thickness and proportionately lower strength in heavier section thicknesses.
2017-09-23
WIP Standard
AMS6474B
This specification establishes requirements for steel forgings of any shape or form that finished parts are to be made (See 8.4, 8.5, 8.8.4 and 8.10).
2017-09-23
WIP Standard
AMS6493B
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. These products have been used typically for carburized parts requiring high minimum core hardness with a narrow range, reduced distortion and subject to stringent magnetic particle inspection standards, but usage is not limited to such applications.
2017-09-23
WIP Standard
AMS6492B
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. These products have been used typically for carburized parts requiring high minimum core hardness with a narrow range, reduced distortion and subject to magnetic particle inspection standards, but usage is not limited to such applications.
2017-09-23
WIP Standard
AMS6496B
This specification covers a nitriding grade of aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. These products have been used typically for nitrided parts such as bearings, operating under heavy loads and high speeds at moderate temperatures, and subject to rigid inspection standards, and requiring highest surface hardness, high core toughness, and less distortion than parts made from steel requiring quenching to case harden, but usage is not limited to such applications.
2017-09-23
WIP Standard
AMS6497B
This specification covers a nitriding grade of premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. These products have been used typically for nitrided parts such as bearings, operating under heavy loads and high speeds at moderate temperatures, and subject to very rigid inspection standards, and requiring highest surface hardness, high core toughness, and less distortion than parts made from steel requiring quenching to case harden, but usage is not limited to such applications.
2017-09-23
WIP Standard
AMS6448M
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
2017-09-23
WIP Standard
AMS6544E
This specification covers a maraging steel in the form of rolled or forged plate.
2017-09-23
WIP Standard
AMS6498B
This specification covers a nitriding grade of premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. These products have been used typically for nitrided parts requiring high minimum core hardness with a narrow range, reduced distortion and subject to stringent magnetic particle inspection standards, but usage is not limited to such applications.
2017-09-23
WIP Standard
AMS6290K
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, and forging stock. These products have been used typically for carburized parts which require low minimum core hardness and allow a wide hardness range in sections 0.375 in. (9.50 mm) and under in nominal thickness, but usage is not limited to such applications. The core may or may not be machinable after hardening.
2017-09-23
WIP Standard
AMS7006
AMS for 718 powder to be used primarily for production of additively manufactured components. The powder could also be used for non-AM applications.
2017-09-23
WIP Standard
AMS6360N
This specification covers an aircraft-quality, low-alloy steel in the form of seamless tubing. This tubing has been typically used in thin wall-thickness sections where minimum tensile strength up to 160,000 psi (1103 MPa) is required and where parts may be welded during fabrication, but usage is not limited to such applications.
2017-09-23
WIP Standard
AMS2251J
This specification covers established inch/pound manufacturing tolerances applicable to low-alloy steel bars ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "exclusive " is used to apply only to the higher figure of the specified range.
2017-09-23
WIP Standard
AMS6346C
This specification covers an aircraft-quality, low-alloy steel in the form of heat treated bars.
2017-09-23
WIP Standard
AMS6348E
This specification covers an aircraft-quality, low-alloy steel in the form of bars. These bars have been used typically for parts, 0.50 inch (12.7 mm) and under in section thickness at time of heat treatment, requiring a through-hardening steel capable of developing hardness as high as 35 HRC when properly hardened and tempered and also parts of greater thickness but requiring proportionately lower hardness, but usage is not limited to such applications.
2017-09-22
WIP Standard
AIR6962
A review of icing materials that would be educational to a designer of a UAV ice protection system is provided. Additionally, the differences between unmanned and manned ice protection systems are explored along with a discussion on how these differences can be addressed.
2017-09-22
WIP Standard
AMS6946D
This specification covers a titanium alloy in the form of sheet, strip, and plate.
2017-09-22
WIP Standard
AMS6945C
This specification covers a titanium alloy in the form of sheet, strip, and plate. <p> These products have been used typically for parts requiring strength up to 750 °F (400 °C), but usage is not limited to such applications.
2017-09-22
WIP Standard
AS6171/23
The intent of this test method is to describe high level processes to detect suspect/counterfeit (SC) Electrical, Electronic, and Electromechanical (EEE) Assemblies, covering both custom and military/commercial off-the-shelf (COTS) assemblies. This standard includes requirements for accreditation and certification of Laboratory and Laboratory personnel, and also, data collection, interpretation, and reporting as applicable to this test method. This standard covers EEE assemblies and includes electronic circuit card assemblies as defined under the definition for EEE Assembly and Electronic Circuit Card Assembly.
2017-09-22
WIP Standard
AS39901C
This standard covers the requirements for non-separable, airframe anti-friction needle bearings, corrosion resistant and traditional materials, intended for use in flight vehicle control systems, with radial loads. Under Department of Defense (DoD) Policies and Procedures, any qualification requirements and associated Qualified Products Lists (QPLs) are mandatory for DoD contracts. Any material relating to QPLs have not been adopted by SAE and are not part of this SAE technical document.
2017-09-22
WIP Standard
AMS4985F
This specification covers a titanium alloy in the form of investiment castings.
2017-09-22
WIP Standard
AMS4937E
This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, and of flash welded rings and stock for flash welded rings.
2017-09-22
WIP Standard
AMS4900Q
This specification covers one grade of commercially-pure titanium in the form of sheet, strip, and plate.
2017-09-22
WIP Standard
AMS4992C
This specification covers titanium Ti 6Al-4V alloy in the form of investment castings.
2017-09-22
WIP Standard
AMS4991F
This specification covers a titanium alloy in the form of investment castings having four grades of permissible discontinuities.
2017-09-22
WIP Standard
AMS4989D
This specification covers a titanium alloy in the form of sheet, strip, and plate.
Viewing 421 to 450 of 35602