Criteria

Text:
Sector:
Content:
Display:

Results

Viewing 811 to 840 of 35602
CURRENT
2017-06-29
Standard
AMS4365
This specification covers an aluminum alloy in the form of plate from 3.000 to 8.000 inches (76.20 to 203.20 mm) in thickness (see 8.4).
CURRENT
2017-06-29
Standard
AMS7875F
This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder.
CURRENT
2017-06-29
Standard
AS90708B
2017-06-29
WIP Standard
AMS2770P

This specification specifies the engineering requirements for heat treatment, by part fabricators (users) or their vendors or subcontractors, of parts (see 8.8.1). It also covers heat treatment by warehouses or distributors converting raw material from one temper to another temper (see 1.3 and 8.5). It covers the following aluminum alloys:

1100, 2004, 2014, 2017, 2024, 2098, 2117, 2124, 2219, 2224, 3003, 5052, 6013, 6061, 6063, 6066, 6951, 7049, 7050, 7075, 7149, 7178, 7249, 7475

CURRENT
2017-06-28
Standard
AS47642B
This document establishes techniques for validating that an Aircraft Station Interface (ASI) complies with the interface requirements delineated in MIL-STD-1760C. For validation of aircraft designed to MIL-STD-1760A Notice 2 AS4764 Issued 1995-04 applies. For validation of aircraft designed to MIL-STD-1760B Notice 3 AS47641 Issued 1999-08 applies.
CURRENT
2017-06-28
Standard
AS47641A
This document establishes techniques for validating that an Aircraft Station Interface (ASI) complies with the interface requirements delineated in MIL-STD-1760B Notice 3. For validation of aircraft designed to MIL-STD-1760A Notice 2 AS4764 Issued 1995-04 applies.
CURRENT
2017-06-28
Standard
AS21906D
CURRENT
2017-06-28
Standard
AS21912D
CURRENT
2017-06-28
Standard
AS21909E
CURRENT
2017-06-28
Standard
AS6316
This SAE Aerospace Standard (AS) documents a common understanding of terms, compliance issues, and occupant injury criteria to facilitate the design and certification of oblique facing passenger seat installations specific to Part 25 aircraft. The applicability of the criteria listed in this current release is limited to seats with an occupant facing direction greater than 18° and no greater than 45° relative to the aircraft longitudinal axis. Seats installed at angles greater than 30° relative to the aircraft longitudinal axis must have an energy absorbing rest or shoulder harness and must satisfy the criteria listed in Table 2. Later revisions are intended to provide criteria for other facing directions. Performance criteria for forward and aft facing seats are provided in AS8049 and for side facing seats in AS8049/1.
CURRENT
2017-06-28
Standard
AMS4375M
This specification covers a magnesium alloy in the form of sheet and plate from 0.016 to 3.000 inches (0.41 to 76.20 mm), inclusive, in thickness (see 8.4).
CURRENT
2017-06-28
Standard
AMS4915M
This specification covers a titanium alloy in the form of sheet, strip, and plate up to 4.000 inches (101.60 mm), inclusive.
CURRENT
2017-06-28
Standard
AS21914D
2017-06-28
WIP Standard
AS50881G
This specification covers all aspects in electrical wire interconnection systems (EWIS) from the selection through installation of wiring and wiring devices and optical cabling and termination devices used in aerospace vehicles. Aerospace vehicles include manned and unmanned airplanes, helicopters, lighter-than-air vehicles, missiles and external pods.
2017-06-27
WIP Standard
ARP6955
This SAE Aerospace Recommended Practice (ARP) document covers the requirements for a Snowcompressor with carrier vehicle used to clear snow from airport operational areas by compressing the volume of collected snow into smaller volumes for loading into a hauling/dump truck or for depositing reduced-volume windrows for snow banking. The term carrier vehicle represents the various self-propelled prime movers that provide the power necessary to move snow and ice control equipment during winter operations. For two-stage rotary plows that primarily are used to cast heavy concentrations of snow away from airport operational areas such as runways and taxiways, see ARP5539.
CURRENT
2017-06-27
Standard
AS4270A
This document establishes techniques for validating that a mission store complies with the interface requirements delineated in MIL-STD-1760.
CURRENT
2017-06-27
Standard
AS4764A
This document establishes techniques for validating that an aircraft station complies with the interface requirements delineated in MIL-STD-1760.
CURRENT
2017-06-27
Standard
AIR6027A
The information presented in this AIR is intended to provide designers of armed unmanned systems with guidelines that may be applied to ensure safe integration and operation of weapons on unmanned platforms. The guidelines have been developed from experiences gained in the design and operation of weapons on manned aircraft that have been accepted by relevant safety authorities in the USA and Europe and proven effective over many years. Whilst the guidelines have been developed from experience with aircraft operations, the concepts are considered equally applicable to non-aircraft systems, such as those used on the surface or undersea environments. This document does not attempt to define or describe a comprehensive safety program for unmanned systems. System Safety is a system characteristic and a non-functional requirement. It has to be addressed at each level of system design, system integration and during each phase of system operation.
2017-06-26
WIP Standard
ARP6481
This SAE Aerospace Recommended Practice (ARP) describes a method for assessing size dependent particle losses in a sampling and measurement system of specified geometry utilizing on the non-volatile PM (nvPM) mass and number concentrations measured at the end of the sampling system. The penetration functions of the sampling and measurement system may be determined either by measurement or by analytic computational methods. Loss mechanisms including thermophoretic (which has a very weak size dependence) and size dependent losses are considered in this method along with the uncertainties due to both measurement error and the assumptions of the method. The results of this system loss assessment allow development of estimated correction factors for nvPM mass and number concentrations to account for the system losses facilitating estimation of the nvPM mass and number at the engine exhaust nozzle exit plane.
CURRENT
2017-06-26
Standard
AS4678D
CURRENT
2017-06-26
Standard
AS4663C
CURRENT
2017-06-26
Standard
AS4666C
CURRENT
2017-06-26
Standard
AS4667B
CURRENT
2017-06-26
Standard
AMS4917J
This specification covers a titanium alloy in the form of sheet, strip, and plate through 4.000 inches (101.6 mm) nominal thickness.
Viewing 811 to 840 of 35602