SAE Technical Standards

Viewing 1 to 50 of 44699
AMS CE Elastomers Committee -
2017-10-19
This specification covers a fluorosilicone (FVMQ) rubber in the form of sheet, strip, and molded shapes.

These products have been used typically for parts requiring resistance to jet fuel and lubric...

WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
AMS CE Elastomers Committee -
2017-10-19
This specification covers a fluorosilicone (FVMQ) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. These products have been used typically for parts requiring resistance to j...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
AMS P Polymeric Materials Committee -
2017-10-19
This specification covers an unfilled, room-temperature-polymerizing epoxy resin formulation with a polyamide hardener, supplied as a two-component system.
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
EG-1A Balancing Committee -
2017-10-18
The primary goal of this new Aerospace Information Report is to provide guidelines to conduct effective Gage R&R studies for balancing tasks. This new Aerospace information report will inform process ...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
Emissions Standards Committee -
2017-10-18
The standard will provide guidance on best practices to ensure consistent, high quality measurements of Particle Number from both raw and dilute vehicle and engine exhaust streams. Key elements will i...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
Battery Materials Testing Committee -
2017-10-18
This SAE RP provides a set of test methods and practices for the characterization of the properties of lithium battery anode active materials. Lithium battery anode active materials can be grouped in ...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
AMS B Finishes Processes and Fluids Committee -
2017-10-18
This is a new specification for the peening process.
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
AMS D Nonferrous Alloys Committee -
2017-10-18
This specification covers an aluminum alloy in the form of extruded profiles (shapes) 0.500 to 1.500 inch, incl (12.7 to 38.1 mm, incl) in nominal thickness, and having a maximum cross-sectional area ...
SAE TECHNICAL STANDARDS
AMS CE Elastomers Committee -
2017-10-18
This specification covers a fluorocarbon (FKM) rubber stock in the form of molded test slabs.
SAE TECHNICAL STANDARDS
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies -
2017-10-18
NO SCOPE AVAILABLE.
SAE TECHNICAL STANDARDS
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies -
2017-10-18
SCOPE IS UNAVAILABLE.
SAE TECHNICAL STANDARDS
Truck Bus Control and Communications Network Committee -
2017-10-18
The purpose of this Recommended Practice is to verify that vehicles and/or components are capable of communicating a required set of information, in accordance with the diagnostic messages specified i...
SAE TECHNICAL STANDARDS
E-25 General Standards for Aerospace and Propulsion Systems -
2017-10-18
SCOPE IS UNAVAILABLE.
SAE TECHNICAL STANDARDS
Hydraulic Hose and Hose Fittings Committee -
2017-10-18
This SAE Standard provides general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment. The general specifications contai...
SAE TECHNICAL STANDARDS
Fuel and Lubricants TC2 Industrial Lubricants -
2017-10-18
The SAE International Industrial Lubricants Committee has developed a number of industrial, non-production lubricant performance specifications. a. Define minimum performance requirements for industri...
SAE TECHNICAL STANDARDS
Fuel and Lubricants TC2 Industrial Lubricants -
2017-10-18
The SAE International Industrial Lubricants Committee has developed a number of industrial, non-production, lubricant performance specifications. The purpose of these voluntary SAE specifications is t...
SAE TECHNICAL STANDARDS
E-25 General Standards for Aerospace and Propulsion Systems -
2017-10-18
This procurement specification covers bolts and screws made from a corrosion and heat resistant, age hardenable nickel base alloy of the type identified under the Unified Numbering System as UNS N0771...
SAE TECHNICAL STANDARDS
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies -
2017-10-18
This SAE Aerospace Standard (AS) covers the requirements for a flexible, lightweight, low pressure, self-extinguishing, silicone hose assembly. The hose has a fully fluorinated fluoropolymer inner lin...
SAE TECHNICAL STANDARDS
E-25 General Standards for Aerospace and Propulsion Systems -
2017-10-18
SCOPE IS UNAVAILABLE.
SAE TECHNICAL STANDARDS
AMS CE Elastomers Committee -
2017-10-18
This specification covers a butyl (IIR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
AMS AM Additive Manufacturing Metals -
2017-10-17
This specification establishes process controls for the repeatable production of aerospace parts by Electron Beam Powder Bed Fusion (EB-PBF). It is intended to be used for aerospace parts manufactured...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
Battery Materials Testing Committee -
2017-10-17
This SAE RP provides a set of test methods and practices for the characterization of the properties of Li-battery separator. The test methods in this RP have been grouped into one of three categories:...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
Road Illumination Devices Standards Committee -
2017-10-16
This SAE standard provides test procedures, performance requirements, design guidelines and installation guidelines for full adaptive forward lighting systems (AFS).
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
Hydraulic Brake Components Standards Committee -
2017-10-16
The scope of this new recommended practice should include, but not necessarily be limited to: 1. Define vehicle operating conditions used to drive MOC-EPB actuator design and selection 2. Define brake...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
EG-1A Balancing Committee -
2017-10-16
Provide guidance on how balance machine vector data is captured and reported. Provide an understanding of how to transform balance machine vector data to alternate locations. Provide guidance on how v...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
EG-1A Balancing Committee -
2017-10-16
Provide a fundamental understanding of reason for completing a bode plot on the balance machine. Discuss potential causes of a resonance within the balance process. Discuss the basis for the WN^2 requ...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
AE-8D Wire and Cable Committee -
2017-10-16
Require an Ethernet cable with electrical parameters equal to the AS6070/2 or /4 with the construction parameters of the /5 or /6.
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
Truck and Bus Foundation Brake Committee -
2017-10-16
This SAE Standard provides test procedures for air, air/hydraulic, and hydraulic drum and disc brakes used on highway commercial vehicles over 4536 kg (10,000 lb) GVWR.
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
G-45 Human Systems Integration -
2017-10-16
The standard would include requirements for HSI management [planning, execution, coordination (internal and external) documentation, administration and quality control], including collaboration among ...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
AMS G Titanium and Refractory Metals Committee -
2017-10-16
This specification provides a standard set of procedures for sampling and testing to meet the requirements of material specifications for wrought titanium and titanium alloy products, except forgings ...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
Aircraft SEAT Committee -
2017-10-16
This document provides an industry-recommended framework for establishing agreements to ensure that seats with integrated electronic components (e.g., actuation system, reading light, inflatable restr...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
AMS D Nonferrous Alloys Committee -
2017-10-15
1.1 Form This specification covers an aluminum-lithium alloy in the form of plate with a product thickness range of 0.500" to 6.500". 1.2 Application This plate has been used typically for parts where...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
AMS G9 Aerospace Sealing Committee -
2017-10-14
This specification covers six (6) types of sealing compounds curing to elastomeric materials.
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
AMS G9 Aerospace Sealing Committee -
2017-10-14
This standard describes the accepted methods used for preparing aerospace sealant test specimens for qualification and quality conformance or acceptance testing. AS5127/1 and AS5127/2 are to be used i...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
AMS D Nonferrous Alloys Committee -
2017-10-13
This specification covers an aluminum alloy in the form of sheet and plate 0.032 to 0.310 inch, incl (0.81 to 7.87 mm, incl) in thickness, clad on both sides (see 8.4).
SAE TECHNICAL STANDARDS
AMS D Nonferrous Alloys Committee -
2017-10-13
This specification covers an aluminum alloy in the form of plate 0.750 to 1.500 inch, incl ( 19.05 to 38.10 mm, incl) in thickness (see 8.5).
SAE TECHNICAL STANDARDS
AMS E Carbon and Low Alloy Steels Committee -
2017-10-13
This specification covers a low-alloy steel in the form of welding wire.
SAE TECHNICAL STANDARDS
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies -
2017-10-13
SCOPE IS UNAVAILABLE.
SAE TECHNICAL STANDARDS
Truck Bus Control and Communications Network Committee -
2017-10-13
This document describes the application of the SAE J1939 recommended practices for compliance with on-board diagnostic malfunction detection system requirements for marine sterndrive and inboard spark...
SAE TECHNICAL STANDARDS
Truck and Bus Brake Systems Committee -
2017-10-13
This code is intended for commercial vehicles over 4500 kg (10 000 lb) with brake systems having typical service pressure ranges 0 to 14.1 mPa (0 to 2050 psi) hydraulic or 0 to 830 kPa (0 to 130 psi) ...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies -
2017-10-13
SCOPE IS UNAVAILABLE.
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies -
2017-10-13
This SAE Aerospace Standard (AS) defines the requirements for a threadless, flexible, high conductive self-bonding coupling assembly which, when installed on defined ferrules, provides a flexible conn...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
MTC8, Tire and Rim -
2017-10-13
This SAE Standard is established for the following purpose: a. simplify the application of radial drive wheel tires to agricultural vehicles especially those with multiple drive axle having tires of d...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
Hybrid - EV Committee -
2017-10-13
This SAE Standard covers the general physical, electrical, functional and performance requirements to facilitate conductive charging of EV/PHEV vehicles in North America. This document defines a commo...
SAE TECHNICAL STANDARDS
Hybrid - EV Committee -
2017-10-12
This SAE Information Report J2931/7 establishes the security requirements for digital communication between Plug-In Electric Vehicles (PEV), the Electric Vehicle Supply Equipment (EVSE) and the utilit...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
Viewing 1 to 50 of 44699