Refine Your Search

Search Results

Standard

COOLING FLOW MEASUREMENT TECHNIQUES

1992-06-01
HISTORICAL
J2082_199206
This SAE Information Report has been prepared by the Standards Committee on Cooling Flow Measurement (CFM) at the request of the SAE Road Vehicle Aerodynamics Forum Committee (RVAC). The committee was formed in January 1985 for the purpose of investigating what measuring techniques are used by automotive product manufacturers to determine air cooling air flow rates and, if possible, to synthesize these into a recommended practice report. Although a great deal is already known about engine cooling, recent concern with fuel conservation has resulted in generally smaller air intakes whose shape and location are dictated primarily by low vehicle drag/high forward speed requirements. The new vehicle intake configurations make it more difficult to achieve adequate cooling under all conditions. They cause cooling flow velocity profiles to become distorted and underhood temperatures to be excessively high.
Standard

Storage Batteries

1992-06-01
HISTORICAL
J537_199206
This SAE Standard serves as a guide for testing procedures of automotive 12 V storage batteries and as a publication providing information on container holddown configuration and terminal geometry. The ratings submitted are to be based on procedures described in this document. The ratings submitted must be of a level that when any subsequent significant sample is tested in accordance with this document, that at least 90% of the batteries shall meet the ratings. The choice of 90% compliance recognizes that batteries consist of many plates and require chemical-electrical formation procedures and small variations in test conditions and procedures can affect the performance of individual batteries. Future Considerations - In order to expedite the release of this revision of the Standard, several topic areas were deferred for consideration in future revisions.
Standard

Reflex Reflectors for Use on Vehicles 2032 Mm Or More in Overall Width

1992-06-01
HISTORICAL
J2041_199206
This SAE Information Report provides test procedures, requirements, and guidelines for reflex reflectors used on vehicles 2032 mm or more in overall width and 7.6 m or more in length. Reflex reflectors conforming to these requirements may also be used on vehicles less than 2032 mm in overall width.
Standard

Spherical and Flanged Sleeve (Compression) Tube Fittings

1992-06-01
HISTORICAL
J246_199206
This SAE Standard covers complete general and dimensional specifications for tube fittings of the spherical and flanged sleeve compression types for use in the piping of air brake systems on automotive vehicles. The spherical sleeve compression type Figures 1A to 5 and Tables 1 to 3 is intended for use with annealed copper alloy tubing per SAE J1149, Type 1. The flanged sleeve compression type Figures 6A to 11 and Tables 4 to 6 is intended for use with nylon tubing per SAE J844. It is not intended to restrict or preclude other designs of a tube fitting for use with SAE J844, air brake tubing. Performance requirements for SAE J844 are covered in SAE J1131. See SAE J1131 for the Performance Requirements of Reusable (Push to Connect) Fittings Intended for Use in Automotive Air Brake Systems.
Standard

Classification System for Rubber Materials

1992-06-01
HISTORICAL
J200_199206
This classification system tabulates the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. NOTE 1: The SAE Committee on Automotive Rubber Specifications (CARS) has the sole responsibility for SAE J200. CARS Works closely with and receives input from ASTM Subcommittee D11.30 on Classification of Rubber Compounds with the goal to keep SAE J200 and ASTM D 2000 technically equivalent. Candidate materials presented for development of new tables or for inclusion in Tables A1 or A2 of SAE J200 or Table X1.1 of ASTM D 2000 shall be initiated with the SAE CARS Committee. The procedure to be followed is detailed in Appendix C of SAE J200. NOTE 2: This document may serve many of the needs of other industries in much the same manner as SAE numbered steels.
Standard

Test Procedure for Parking Stability of Motorcycles

1992-06-01
HISTORICAL
J1101_199206
Side stands and center stands are designed to support stationary two wheel motorcycles. This SAE Recommended Practice establishes procedures for determining parking surface loading and stability limits as follows: a. The footprint pressure exerted on a horizontal parking surface by the stand, b. The tilt angle of the parking surface at which tip-over occurs, and c. the tilt angle of the parking surface at which roll-off occurs.
Standard

Constant Volume Sampler System for Exhaust Emissions Measurement

1992-06-01
HISTORICAL
J1094_199206
This SAE Information Report describes uniform laboratory techniques for employing the constant volume sampler (CVS) system in measuring various constituents in the exhaust gas of gasoline engines installed on passenger cars and light trucks. The techniques described relate particularly to CVS systems employing positive displacement pumps. In some areas of CVS practice, alternate procedures are given as a guide toward development of uniform laboratory techniques.
Standard

Operator Space Envelope Dimensions for Off-Road Machines

1992-06-01
HISTORICAL
J154_199206
This SAE Standard defines the minimum normal operating space envelope for clothed seated (SAE J899 seat configuration) and standing operators (95th percentile operator, SAE J833). This document applies to off-road, self-propelled work machines used in construction, general purpose industrial, agricultural, and forestry as identified in SAE J1116. This document defines dimensions for the minimum normal operating space envelope around the operator for operator enclosures (cabs, ROPS, FOPS) on off-road machines.
Standard

AIRCRAFT BRAKE TEMPERATURE MONITOR SYSTEMS (BTMS)

1992-06-01
HISTORICAL
AS1145A
This specification covers minimum requirements for brake temperature monitoring equipment whenever used on any type and model of civil aircraft. It shall be the responsibility of the purchaser to determine the compatibility of these requirements with the application aircraft and to specify requirements in excess of these minimums as necessary.
Standard

Specification Definitions-Loaders

1992-06-01
HISTORICAL
J732_199206
This SAE standard provides uniform definitions of specification terms peculiar to loaders as defined in SAE J1057. The specifications must be qualified by stating the track shoe type, width or the tire type, size, ply, and specified inflation pressure; the model number or type of bucket disregarding teeth; and the type and amount of counterweight and/or ballast, if any, with which the machine is equipped. Paragraphs 4.1 and 4.16 are further defined by Figures 1 to 4. The figures are not intended to be exactly descriptive of any particular machine.
X