Refine Your Search

Search Results

Standard

SHEET AND STRIP SURFACE FINISH NOMENCLATURE

1991-01-01
HISTORICAL
AS4194
This SAE Aerospace Standard (AS) defines the nomenclature for surface finishes commonly used for sheet and strip in aerospace material specifications. It is applicable to steel and to iron, nickel, cobalt, and titanium base alloys.
Standard

Electrical Propulsion Control-Off-Road Dumpers

1991-01-01
HISTORICAL
J1299_199101
This SAE Information Report applies to the control circuits and devices associated with the electrical propulsion system used on electric drive dumpers. Dumper is defined in J/ISO 6165. The document does not apply to auxiliary equipment control systems such as: a. battery charging systems; b. engine wiring and control; c. monitoring and control circuits not directly affecting the operation of the electric propulsion and retarding system; d. lighting; and e. accessory systems (heating, air conditioning, horns, radios, emergency steering, fire protection, and similar functions). This document establishes requirements for the control circuits and control devices of the electric propulsion system of an electric drive dumper. Criteria are established for environmental service conditions, control systems requirements, control device operational requirements and control tests.
Standard

Performance Requirements for the Automotive Audio Cassette

1991-01-01
CURRENT
J1274_199101
This performance document for the audio cassette was developed by qualified engineers from the automotive industry, the prerecorded tape industry, and the tape and cassette manufacturers. It is based upon sound engineering principles supported by laboratory tests and field experience. The values given are supported by all of these industries and considered necessary to establish customer acceptance and satisfaction.
Standard

OFF-ROAD TIRE AND RIM SELECTION AND APPLICATION

1991-01-01
CURRENT
J1315_199101
This SAE Standard provides general guidelines for the proper selection and application of off-road tires and rims; as defined in SAE J751 APR86; and applied to earthmoving machines described in SAE J1116 JUN86 and J1057 JUN81.
Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims

1991-01-01
HISTORICAL
J1095_199101
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of spoke wheels and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). It is up to each hub and/or spoke wheel developer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or spoke wheel developer to modify other parameters to obtain satisfactory service life.
Standard

Labeling of Rops and Fops and Ops

1991-01-01
HISTORICAL
J1164_199101
This SAE Standard establishes the specifications and content for labeling of ROPS, FOPS, and OPS, which may commonly be a part of construction, forestry, mining, and industrial machines. The label content herein shall be applied to a ROPS and/or FOPS and/or OPS on any of these machines.
Standard

Determination of Chlorine in Oxygen from Solid Chemical Oxygen Generators

1991-01-01
HISTORICAL
ARP1320A
This ARP covers a procedure to be used in the determination of 0.05 to 0.3 ppm of chlorine in oxygen from any type of generator used for emergency or other life-support systems. The methyl orange method described can be considered as a referee technique. Instrumental analysis is also given in Section 8.
Standard

Silver Alloy, Brazing Filler Metal, 45Ag - 24Cd - 16Zn - 15Cu, 1125 to 1145 °F (607 to 618 °C) Solidus-Liquidus Range

1991-01-01
HISTORICAL
AMS4769D
This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips, and a viscous mixture (paste) of powder in a suitable binder. This material has been used typically for torch or induction brazing of ferrous metals, including austenitic steels and alloys, where high joint strength up to 400 degrees F (207 degrees C) is required, and for joining nonferrous metals except those having base of aluminum or magnesium, but usage is not limited to such applications.
Standard

Silver Alloy, Brazing Filler Metal, 56Ag - 42Cu - 2.0Ni, 1420 to 1640 °F (771 to 893 °C) Solidus-Liquidus Range

1991-01-01
HISTORICAL
AMS4765C
This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, chips, and a viscous mixture (paste) of powder in a suitable binder. This material has been used typically for joining ferrous metals, particularly austenitic steels and alloys, by atmosphere furnace brazing without flux, where high joint strength up to 800 degrees F (427 degrees C) is required, or for nonferrous metals except those having base of aluminum or magnesium, but usage is not limited to such applications.
Standard

Silver Alloy Brazing Filler Metal, 50Ag - 18Cd - 16.5Zn - 15.5Cu, 1160 to 1175 °F (627 to 635 °C) Solidus-Liquidus Range

1991-01-01
HISTORICAL
AMS4770H
This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips, and a viscous mixture (paste) of powder in a suitable binder. This material has been used typically for torch or induction brazing ferrous metals and copper alloys, where high joint strength up to 400 degrees F (204 degrees C) and low brazing temperatures are required, but usage is not limited to such applications.
X