This procurement specification covers aircraft quality self-locking nuts for wrenching (hex, spline) and anchor (plate, gang channel, shank) types of nuts made from a corrosion and heat resistant nickel-base alloy of the type identified under the Unified Numbering System as UNS N07001. Tension height nuts having overall length of threaded portion not less than 1.2 times the nominal thread diameter have 1210 MPa minimum tensile strength at room temperature. Shear height nuts having shorter threaded portion have 1100 MPa minimum tensile strength at room temperature. Maximum test temperature of parts is 730°C
This procurement specification covers aircraft quality metric spanner nuts for retaining shaft mounted parts. Nuts are made from a corrosion and heat resistant age hardenable iron base alloy of the type identified under the Unified Numbering System as UNS S66286, and silver plated. Thread shear proof strength at room temperature is 450 MPa.
Ground-to-air selective calling system characteristics are defined by this standard. The system allows selective calling of individual aircraft over radio communications circuits linking the ground station to the aircraft. Elements comprising overall system are ground selecting calling unit (coder), ground-to-air transmitter (HF or VHF), airborne receiver (HF or VHF), airborne selective calling unit (decoder), and code selection panel.
This procurement specification covers the requirements for metal tube support clamps comprising of two spring clips made of corrosion and heat resistant steel and the associated PTFE single split cushion that supports the tube. See Figure 1.
This Aerospace Recommended Practice (ARP) defines and establishes design, construction, and performance requirements for a flexible, reuseable, water-vaporproof cover for environmental protection of internal combustion engines, major components, and other military and commercial items (see 6.1).
This SAE Aerospace Information Report (AIR) identifies and summarizes the various factors that must be considered and evaluated by the design or specifying engineer in establishing the specifications and design characteristics of battery-powered aircraft tow tractors. This AIR is presented in two parts. The first part is simply a summarization of design factors that must be considered in establishing vehicle specifications and design characteristics. The second part refers particularly to the performance characteristics of an aircraft tow tractor. Some definitions, formulas, data, and an example are provided mainly for assisting the specifying engineers of potential buyers and users of aircraft tow tractors in the evaluation and comparison of their requirements with the performance capabilities of the various tow tractors offered by the tow tractor manufacturers.
This report describes basic methods, typical results, limitations, and technical variables which may provide some relative performance expectations for different lots of the same material, or comparison characteristics for different materials. This testing alone does not assure satisfactory operation in the engine, i.e., there is not a direct relationship to actual engine performance.
The primary measurement procedure recommended in this ARP includes the recording of sound pressure signals in the interior of an airplane during steady state cruise conditions with analysis after the flight into octave band (or one-third octave band) sound pressure levels.
This Aerospace Recommended Practice (ARP) describes the continuous sampling and analysis of gaseous emissions from aircraft gas turbine engines and is intended to standardize the emission test procedures1 and equipment for measuring carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and total hydrocarbons. This ARP is not intended for in-flight testing, nor does it apply to engines operating in the afterburning mode.
This SAE Aerospace Recommended Practice (ARP) defines minimum requirements for an aircraft transport ULD to transport horses properly and safely by air, to protect the horse(s) from injuries and to protect the aircraft from corrosion created by waste spill. The ULD is designed to accommodate one horse or several. There are two types of ULDs for aircraft transportation of horses: Type 1: The ULD is an airworthiness certified structural container, satisfying the requirements of NAS 3610 for the appropriate base size. Type 2: The ULD consists of a self-contained stall which is positioned on a standard aircraft pallet and restrained to the pallet by means of a cargo pallet net or by straps.
This SAE Recommended Practice applies to those air brake system valves used to control the vehicle service brakes and test procedures defined by SAE J1859 to measure performance characteristics. This Recommended Practice adheres to standard industry practice of using English units for specifying valve characteristics.
This SAE Aerospace Recommended Practice (ARP) is intended to interpret and clarify engineering drawing requirements relating to the manufacture and inspection of fluid tube fittings and connectors. Because it is impractical to define every minute detail of the part on the face of the drawing, this document describes general machining tolerances that fall under the heading of, "good shop practice". This document serves as a supplement to engineering drawings when referenced on applicable documents.
This SAE Recommended Practice establishes a uniform procedure for assuring the manufactured quality, installed utility, and service performance of certain automotive adaptive products, other than those provided by the vehicle manufacturer, intended to provide driving capability to persons with physical disabilities. These devices function as adaptive appliances to compensate for lost or reduced performance in the arms or legs, or both, of the driver. Some of the devices are designed to transfer foot functions to the hands, hand functions to the feet, or functions from one side of the body to the other.
This SAE Standard specifies requirements for two types, three classes and four styles of reinforced hose and non-reinforced tubing for conveying gasoline or diesel fuel aboard small craft including pleasure craft whose fuel systems are regulated under 33 CFR 183 Subpart J. Refer to SAE J1942 Hose and Hose Assemblies for commercial marine nonmetallic flexible hose or hose assemblies used in systems on board commercial vessels inspected and certified by the U.S. Coast Guard. Refer to SAE J2046 Personal Watercraft Fuel Systems for fuel hose used on Personal Watercraft.
To establish a quality control procedure suitable for both users and producers by which the cleanliness level of new hydraulic fluid can be quantified, certified, and specified. The method is applicable to new mineral and synthetic hydraulic fluids--regardless of packaging. This sAE Standard is not intended as a procedure for operating equipment.