Refine Your Search

Search Results

Standard

Companion Flanges, Type A (External Pilot) and Type S (Internal Pilot)

1990-06-01
HISTORICAL
J1946_199006
This SAE Standard specifies the nominal dimensions and tolerances which affect the interchangeability between companion flanges and mating parts. The flanges covered by this document are designated type A and type S. The type A flanges are equivalent to type A ISO 7646. The type S flanges are equivalent to the type S ISO 7647. Type A is an external (male) pilot construction and type S is an internal (female) pilot construction. These flanges are not interchangeable. Dimensions not specified are left to the discretion of the component manufacturer.
Standard

Engine Charge Air Cooler (CAC) Nomenclature

1990-06-01
HISTORICAL
J1148_199006
This SAE Recommended Practice is intended to outline basic nomenclature and terminology in common use for engine charge air coolers, related charge air cooling system components, and charge air operating and performance parameters. An engine charge air cooler is a heat exchanger used to cool the charge air of an internal combustion engine after it has been compressed by an exhaust gas driven turbocharger, an engine driven turbocharger, or a mechanically or electrically driven blower. The use of a charge air cooler allows increased engine horsepower output, and may reduce emission levels and improve fuel economy through a more complete combustion due to the increased air density available. Typical cooling media includes the engine's coolant, ambient air, or an external water or coolant source.
Standard

Tubing-Motor Vehicle Brake System Hydraulic

1990-06-01
HISTORICAL
J1047_199006
This is a performance requirement qualification specification intended to give reasonable flexibility in the initial engineering selection of materials when fabricated by currently accepted manufacturing processes. It is not intended to be used for quality control purposes. This SAE Recommended Practice covers the tubing intended primarily for use as hydraulic brake lines on motor vehicles. It covers materials, manufacturing processes, and general properties required to meet the wide range of service encountered in automotive applications. To meet this need, it must be formed, assembled, handled, and installed in accordance with sound engineering and manufacturing practices. This specification covers only the basic tubing and does not include attachments such as protective armor or end fittings.
Standard

Spherical and Flanged Sleeve (Compression) Tube Fittings

1990-06-01
HISTORICAL
J246_199006
This SAE Standard covers complete general and dimensional specifications for tube fittings of the spherical and flanged sleeve compression types for use in the piping of air brake systems on automotive vehicles. The spherical sleeve compression type Figures 1A to 5 and Tables 1 to 3 is intended for use with annealed copper alloy tubing per SAE J1149, Type 1. The flanged sleeve compression type Figures 6A to 11 and Tables 4 to 6 is intended for use with nylon tubing per SAE J844. It is not intended to restrict or preclude other designs of a tube fitting for use with SAE J844, air brake tubing. Performance requirements for SAE J844 are covered in SAE J1131. See SAE J1131 for the Performance Requirements of Reusable (Push to Connect) Fittings Intended for Use in Automotive Air Brake Systems.
Standard

High-Strength Carbon and Alloy Die Drawn Steels

1990-06-01
HISTORICAL
J935_199006
This SAE Recommended Practice is intended to provide basic information on properties and characteristics of high-strength carbon and alloy steels which have been subjected to special die drawing. This includes both cold drawing with heavier-than-normal drafts and die drawing at elevated temperatures.
Standard

Alternative Automotive Fuels

1990-06-01
HISTORICAL
J1297_199006
This SAE Information Report provides information on certain fuels that are being used or have been suggested as alternatives to motor gasoline (SAE J312) or automotive diesel fuel (SAE J313) for use in spark-ignition or compression-ignition engines. Some of these fuels are derived from petroleum while others are from non petroleum sources.
Standard

Motor Vehicle Brake Fluid

1990-06-01
HISTORICAL
J1703_199006
This SAE Standard covers motor vehicle brake fluids of the nonpetroleum type for use in the braking system of any motor vehicle such as a passenger car, truck, bus, or trailer. These fluids are not intended for use under arctic conditions. These fluids are designed for use in braking systems fitted with rubber cups and seals made from styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM).
Standard

Axle Efficiency Test Procedure

1990-06-01
HISTORICAL
J1266_199006
Data from this SAE Recommended Practice permit mapping axle efficiency and/or waste energy over the operating range of trucks, busses, and other highway vehicles based on truck chasses. The procedure can be applied to single axles, tandem axles as a system, or other systems, by combining separate tests, such as tests of the front axle and power divider and rear axle of tandem or tri-drive type.
Standard

Performance Requirements for Motor Vehicle Headlamps

1990-06-01
HISTORICAL
J1383_199006
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements for headlamps.
Standard

Automotive Tube Fittings

1990-06-01
HISTORICAL
J512_199006
This SAE Standard covers complete general and dimensional specifications for the various types of tube fittings intended for general application in the automotive, appliance, and allied fields. See SAE J1131 for the performance requirements of reusable (push to connect) fittings intended for use in automotive air brake systems.
Standard

Refrigeration Tube Fittings - General Specifications *HS-150/2000*

1990-06-01
HISTORICAL
J513_199006
This SAE Standard covers complete general and dimensional specifications for refrigeration tube fittings of the flare type specified in Figures 1 to 42 and Tables 1 to 15. These fittings are intended for general use with flared annealed copper tubing in refrigeration applications. Dimensions of single and double 45 degree flares on tubing to be used in conjunction with these fittings are given in Figure 2 and Table 1 of SAE J533. The following general specifications supplement the dimensional data contained in Tables 1 to 15 with respect to all unspecified details.
Standard

Road Vehicle--Hydraulic Brake Hose Assemblies for Use With Nonpetroleum-Base Hydraulic Fluids

1990-06-01
HISTORICAL
J1401_199006
This SAE Standard specifies the performance tests and requirements for hydraulic brake hose assemblies used in the hydraulic braking system of a road vehicle. It also specifies the methods used for identification of the hose manufacturer. This document applies to brake hose assemblies made of a hose fabricated from yarn and natural or synthetic elastomers and assembled with metal end fittings for use with nonpetroleum-base brake fluids as specified in SAE J1703 and SAE J1705. The nominal internal diameter of the brake hose shall fall within one of the following values: 3.5 mm or less (1/8 in or less) 4 to 5 mm (3/16 in)
Standard

Classification System for Rubber Materials

1990-06-01
HISTORICAL
J200_199006
This classification system tabulates the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. NOTE 1: The SAE Committee on Automotive Rubber Specifications (CARS) has the sole responsibility for SAE J200. CARS Works closely with and receives input from ASTM Subcommittee D11.30 on Classification of Rubber Compounds with the goal to keep SAE J200 and ASTM D 2000 technically equivalent. Candidate materials presented for development of new tables or for inclusion in Tables A1 or A2 of SAE J200 or Table X1.1 of ASTM D 2000 shall be initiated with the SAE CARS Committee. The procedure to be followed is detailed in Appendix C of SAE J200. NOTE 2: This document may serve many of the needs of other industries in much the same manner as SAE numbered steels.
Standard

Hydraulic Hose Fittings

1990-06-01
HISTORICAL
J516_199006
This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 15 are applicable to all hydraulic hose fittings and supplement the detailed specifications for the 100R-series fittings contained in the later sections of this document. This document shall be utilized as a procurement document only to the extent agreed upon by the manufacturer and user. Refer to SAE J517 for specifications of hose and information on hose assemblies. SAE J1273 contains information on application factors affecting hose fittings, hose, and hose assemblies. THE RATED WORKING PRESSURE OF A HOSE ASSEMBLY COMPRISING SAE J516 FITTINGS AND SAE J517 HOSE SHALL NOT EXCEED THE LOWER OF THE TWO WORKING PRESSURE RATED VALUES.
Standard

Nonmetallic Air Brake System Tubing

1990-06-01
HISTORICAL
J844_199006
This SAE Standard covers the minimum requirements for nonmetallic tubing as manufactured for use in air brake systems. Nonreinforced products are designated type A and reinforced products type B. It is not intended to cover tubing for any portion of the system which operates below -40 degree C (-40 degrees F), above +93 degrees C (+200 degrees F), above a maximum working gage pressure of 1030 kPa (150 psi), or in an area subject to attack by battery acid. This tubing is intended for use in the brake system for connections which maintain a basically fixed relationship between components during vehicle operation. Coiled tube assemblies required for those installations where flexing occurs are covered by this document and SAE J1131 to the extent of setting minimum requirements on the essentially straight tube and tube fitting connections which are used in the construction of such assemblies.
Standard

Engine Oil Performance and Engine Service Classification (Other than "Energy Conserving")

1990-06-01
HISTORICAL
J183_199006
This SAE Standard outlines the engine oil performance categories and classifications developed through the efforts of the Alliance of Automobile Manufacturers (Alliance), American Petroleum Institute (API), the American Society for Testing and Materials (ASTM), the Engine Manufacturers Association (EMA), International Lubricant Standardization and Approval Committee (ILSAC) and SAE. The verbal descriptions by API and ASTM, along with prescribed test methods and limits are shown for active categories in Table 1 and obsolete categories in Table A1. Appendix A is a historical documentation of the obsolete categories. For purposes of this document, active categories are defined as those (a) for which the required test equipment and test support materials, including reference engine oils and reference fuels, are readily available, (b) for which ASTM or the test developer monitors precision for all tests, and (c) which are currently available for licensing by API EOLCS.
Standard

Specification for O-ring Materials Used with Hydraulic Connectors

1990-06-01
HISTORICAL
J515_199006
SAE J515 covers the specification for hydraulic O-ring material and properties and sizes applicable to face seal fittings, metric and inch stud ends, and four-bolt flange fittings. The standard includes a size code to allow industry and government agencies to order O-ring with a coded part number.
Standard

Rubber Seals for Hydraulic Disc Brake Cylinders

1990-06-01
HISTORICAL
J1603_199006
This SAE Standard describes the performance and part requirements for elastomeric seals used in highway vehicle disc brake calipers. Seals covered by this specification may be the solid section type (square, rectangular, O-ring, etc.) mounted stationary in the cylinder bore or on the movable piston. The specification contains the following major sections:
X