Criteria

Text:
Content:
Display:

Results

Viewing 541 to 570 of 45192
2017-09-23
WIP Standard
AMS6290K
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, and forging stock. These products have been used typically for carburized parts which require low minimum core hardness and allow a wide hardness range in sections 0.375 in. (9.50 mm) and under in nominal thickness, but usage is not limited to such applications. The core may or may not be machinable after hardening.
2017-09-23
WIP Standard
AMS7006
AMS for 718 powder to be used primarily for production of additively manufactured components. The powder could also be used for non-AM applications.
2017-09-23
WIP Standard
AMS6360N
This specification covers an aircraft-quality, low-alloy steel in the form of seamless tubing. This tubing has been typically used in thin wall-thickness sections where minimum tensile strength up to 160,000 psi (1103 MPa) is required and where parts may be welded during fabrication, but usage is not limited to such applications.
2017-09-23
WIP Standard
AMS2251J
This specification covers established inch/pound manufacturing tolerances applicable to low-alloy steel bars ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "exclusive " is used to apply only to the higher figure of the specified range.
2017-09-23
WIP Standard
AMS6346C
This specification covers an aircraft-quality, low-alloy steel in the form of heat treated bars.
2017-09-23
WIP Standard
AMS6348E
This specification covers an aircraft-quality, low-alloy steel in the form of bars. These bars have been used typically for parts, 0.50 inch (12.7 mm) and under in section thickness at time of heat treatment, requiring a through-hardening steel capable of developing hardness as high as 35 HRC when properly hardened and tempered and also parts of greater thickness but requiring proportionately lower hardness, but usage is not limited to such applications.
2017-09-22
WIP Standard
AIR6962
A review of icing materials that would be educational to a designer of a UAV ice protection system is provided. Additionally, the differences between unmanned and manned ice protection systems are explored along with a discussion on how these differences can be addressed.
2017-09-22
WIP Standard
AMS6946D
This specification covers a titanium alloy in the form of sheet, strip, and plate.
2017-09-22
WIP Standard
AMS6945C
This specification covers a titanium alloy in the form of sheet, strip, and plate. <p> These products have been used typically for parts requiring strength up to 750 °F (400 °C), but usage is not limited to such applications.
2017-09-22
WIP Standard
J1098
This SAE Standard establishes the procedures for the application of Tonne Kilometer Per Hour (TKPH) rating values for off-the-road tires; utilizing empirical data formula, it describes the procedure for evaluating and predicting off-the-road tire TKPH requirements as determined by a work cycle analysis.
2017-09-22
WIP Standard
J987
This SAE Standard applies to mobile construction-type lifting cranes utilizing rope-supported, conventional and luffing type lattice boom crane structures.
2017-09-22
WIP Standard
AS6171/23
The intent of this test method is to describe high level processes to detect suspect/counterfeit (SC) Electrical, Electronic, and Electromechanical (EEE) Assemblies, covering both custom and military/commercial off-the-shelf (COTS) assemblies. This standard includes requirements for accreditation and certification of Laboratory and Laboratory personnel, and also, data collection, interpretation, and reporting as applicable to this test method. This standard covers EEE assemblies and includes electronic circuit card assemblies as defined under the definition for EEE Assembly and Electronic Circuit Card Assembly.
2017-09-22
WIP Standard
AS39901C
This standard covers the requirements for non-separable, airframe anti-friction needle bearings, corrosion resistant and traditional materials, intended for use in flight vehicle control systems, with radial loads. Under Department of Defense (DoD) Policies and Procedures, any qualification requirements and associated Qualified Products Lists (QPLs) are mandatory for DoD contracts. Any material relating to QPLs have not been adopted by SAE and are not part of this SAE technical document.
CURRENT
2017-09-22
Standard
CPKW1_17FT651V
This product includes information on the manufacturer, engine, application, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds
CURRENT
2017-09-22
Standard
CPKW1_17FT691V
This product includes information on the manufacturer, engine, application, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds.
CURRENT
2017-09-22
Standard
CPKW2_17FT651V
This product includes information on the manufacturer, engine, applications, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds. In addition, this product contains complete engine information such as displacement, cylinder configuration, valve train, combustion cycle, pressure charging, charge air cooling, bore, stroke, cylinder numbering convention, firing order, compression ratio, fuel system, fuel system pressure, ignition system, knock control, intake manifold, exhaust manifold, cooling system, coolant liquid, thermostat, cooling fan, lubricating oil, fuel, fuel shut off speed, etc. Also included are all measured test parameters outlined in J2723.
CURRENT
2017-09-22
Standard
CPKW2_17FT691V
This product includes information on the manufacturer, engine, applications, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds. In addition, this product contains complete engine information such as displacement, cylinder configuration, valve train, combustion cycle, pressure charging, charge air cooling, bore, stroke, cylinder numbering convention, firing order, compression ratio, fuel system, fuel system pressure, ignition system, knock control, intake manifold, exhaust manifold, cooling system, coolant liquid, thermostat, cooling fan, lubricating oil, fuel, fuel shut off speed, etc. Also included are all measured test parameters outlined in J2723.
2017-09-22
WIP Standard
AMS4985F
This specification covers a titanium alloy in the form of investiment castings.
2017-09-22
WIP Standard
AMS4937E
This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, and of flash welded rings and stock for flash welded rings.
2017-09-22
WIP Standard
AMS4900Q
This specification covers one grade of commercially-pure titanium in the form of sheet, strip, and plate.
2017-09-22
WIP Standard
AMS4992C
This specification covers titanium Ti 6Al-4V alloy in the form of investment castings.
2017-09-22
WIP Standard
AMS4991F
This specification covers a titanium alloy in the form of investment castings having four grades of permissible discontinuities.
CURRENT
2017-09-22
Standard
CPKW2_17FT730V
This product includes information on the manufacturer, engine, applications, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds. In addition, this product contains complete engine information such as displacement, cylinder configuration, valve train, combustion cycle, pressure charging, charge air cooling, bore, stroke, cylinder numbering convention, firing order, compression ratio, fuel system, fuel system pressure, ignition system, knock control, intake manifold, exhaust manifold, cooling system, coolant liquid, thermostat, cooling fan, lubricating oil, fuel, fuel shut off speed, etc. Also included are all measured test parameters outlined in J2723.
CURRENT
2017-09-22
Standard
CPKW1_17FT730V
This product includes information on the manufacturer, engine, application, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds.
2017-09-22
WIP Standard
AMS4989D
This specification covers a titanium alloy in the form of sheet, strip, and plate.
CURRENT
2017-09-22
Standard
J1752/3_201709
This measurement procedure defines a method for measuring the electromagnetic radiation from an integrated circuit (IC). The IC being evaluated is mounted on an IC test printed circuit board (PCB) that is clamped to a mating port (referred to as a wall port) cut in the top or bottom of a TEM or wideband TEM (GTEM) cell. The test board is not in the cell as in the conventional usage but becomes a part of the cell wall. This method is applicable to any TEM or GTEM cell modified to incorporate the wall port; however, the measured RF voltage is affected by the septum to test board (wall) spacing. This procedure was developed using a 1 GHz TEM cell with a septum to wall spacing of 45 mm and a GTEM cell with average septum to wall spacing of 45 mm over the port area. Other cells may not produce identical spectral output but may be used for comparative measurements, subject to their frequency and sensitivity limitations.
Viewing 541 to 570 of 45192