Refine Your Search

Search Results

Standard

CHEMICAL CHECK ANALYSIS LIMITS Wrought Nickel Alloys and Cobalt Alloys

1988-07-01
HISTORICAL
AMS2269D
This specification covers chemical check (product or verification) analysis limits for wrought nickel alloys and cobalt alloys having nominal compositions made up of elements, other than iron, that comprise more than 50% of the total. The chemical check analysis limits shown herein shall apply when this specification is referenced in the material specification. Check analysis limits for elements or for ranges of elements not listed herein shall be as specified in the applicable material specification or as agreed upon by purchaser and vendor.
Standard

Chemical Check Analysis Limits Nickel, Nickel Alloys, and Cobalt Alloys

1994-08-01
HISTORICAL
AMS2269E
This specification defines limits of variation for determining acceptability of the chemical composition of cast or wrought nickel, nickel alloy, and cobalt alloy parts and material acquired from a producer. Check analysis limits for elements or for ranges of elements not listed herein shall be as specified in the applicable material specification or as agreed upon by purchaser and vendor.
Standard

Tolerances Rubber Products

1993-07-01
HISTORICAL
AMS2279A
This specification covers established inch/pound manufacturing tolerances applicable to non-cellular rubber products ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "exclusive" applies only to the higher figure of the specified range.
Standard

TOLERANCES Rubber Products

1986-01-01
HISTORICAL
AMS2279
This specification covers established inch/pound manufacturing tolerances applicable to non-cellular rubber products ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" applies only to the higher figure of the specified range.
Standard

Tolerances Rubber Products

2011-11-07
CURRENT
AMS2279B
This specification covers established inch/pound manufacturing tolerances applicable to non-cellular rubber products ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "exclusive" applies only to the higher figure of the specified range.
Standard

Tolerances, Nickel, Nickel Alloy, and Cobalt Alloy Bars, Rods, and Wire

2018-02-02
WIP
AMS2261L
This specification covers established manufacturing tolerances applicable to bars, rods, and wire of nickel, nickel alloy, and cobalt alloys ordered to inch-pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" is used to apply only to the higher figure of a specified range. Where the terms “nickel”, “nickel-copper”, “nickel-chromium”, “nickel-molybdenum”, “nickel-molybdenum-chromium”, and “cobalt” are used without qualification, they refer to both non-heat-treatable and heat-treatable alloys as applicable, unless otherwise noted.
Standard

Tolerances Nickel, Nickel Alloy, and Cobalt Alloy Bars, Rods, and Wire

2009-09-28
HISTORICAL
AMS2261J
This specification covers established manufacturing tolerances applicable to bars, rods, and wire of nickel, nickel alloy, and cobalt alloys ordered to inch-pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term “excl” is used to apply only to the higher figure of a specified range.
Standard

Tolerances Nickel, Nickel Alloy, and Cobalt Alloy Bars, Rods, and Wire

2012-10-08
CURRENT
AMS2261K
This specification covers established manufacturing tolerances applicable to bars, rods, and wire of nickel, nickel alloy, and cobalt alloys ordered to inch-pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" is used to apply only to the higher figure of a specified range.
Standard

Tolerances Nickel, Nickel Alloy, and Cobalt Alloy Bars, Rods, and Wire

2007-07-13
HISTORICAL
AMS2261H
This specification covers established manufacturing tolerances applicable to bars, rods, and wire of nickel, nickel alloy, and cobalt alloys ordered to inch-pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term “excl” is used to apply only to the higher figure of a specified range.
X