Criteria

Text:
Content:
Display:

Results

Viewing 37381 to 37410 of 37599
HISTORICAL
1983-03-01
Standard
AS1791
Scope unavailable.
CURRENT
2017-09-05
Standard
AS13001A
This standard establishes the common requirements for training of DPRV personnel for use at all levels of the aerospace engine supply chain. This standard shall apply when an organization elects to delegate product release verification by contractual flow down to its suppliers (reference 9100 and 9110 standards) and to perform product acceptance on its behalf. It is intended that organizations specify their DPRV requirements through the application of AS9117. While the delegating organization will use the AS13001 standard as the baseline for establishing DPRV process and product training, it may include additional contractual training requirements to meet its specific needs. The DPRV training material was primarily developed for aerospace engine supply chain requirements. However, this standard may also be used in other aerospace industry sectors where a DPRV process requiring specific training can be of benefit.
HISTORICAL
1993-08-04
Standard
AS1791B
HISTORICAL
1993-04-01
Standard
AS1791A
Scope unavailable.
HISTORICAL
1990-01-01
Standard
AS1043E
HISTORICAL
2015-02-02
Standard
AS13001
The standard applies to aero engine suppliers operating a self-release process as a delegated activity from the delegating organization. While primarily developed around the aero engine supply chain requirements, this standard can also be used in other industry sectors where a self-release process may be of benefit.
CURRENT
2017-05-25
Standard
AS1043G
SCOPE IS UNAVAILABLE.
HISTORICAL
1979-03-01
Standard
AS1043B
No scope available.
HISTORICAL
1966-05-01
Standard
AS1043A
No scope available.
HISTORICAL
1989-02-01
Standard
AS1043D
HISTORICAL
1980-08-01
Standard
AS1043C
No scope available.
CURRENT
2012-11-19
Standard
ARP4105C
This document is intended to establish preferred abbreviations and acronyms for terms used on panels, controls, displays, instruments, placards, and markings. The recommendations apply to equipment used by crew members in the flight deck of transport aircraft.
2010-09-20
WIP Standard
ARIR431
This is a final Report of the Avionics Maintenance Conference (AMC) Task Group 116 which was formed to discover the causes of "No Fault Found" in avionics equipment during test. This standard identifies sources of this problem and provides recommendations for its improvement.
1961-06-01
WIP Standard
ARIR407-1
The Synchro System Manual provides valuable information to designers and maintainers of avionics equipment that employ synchro devices. Synchro theory, synchro applications and signal definitions are included in this standard. Originally published in 1950, it is considered to be the classic guide for synchro devices.The Synchro System Manual provides valuable information to designers and maintainers of avionics equipment that employ synchro devices. Synchro theory, synchro applications and signal definitions are included in this standard. Originally published in 1950, it is considered to be the classic guide for synchro devices. The Synchro System Manual provides valuable information to designers and maintainers of avionics equipment that employ synchro devices. Synchro theory, synchro applications and signal definitions are included in this standard. Originally published in 1950, it is considered to be the classic guide for synchro devices.
HISTORICAL
1999-11-01
Standard
ARP5413
This SAE Aerospace Recommended Practice (ARP) provides guidance for a means of showing compliance with the regulations for hazards caused by the lightning environment to electrical/electronic systems installed either on or within aircraft. Equipment hazards addressed include those due to indirect effects on equipment and its associated wiring that is mounted on the aircraft exterior as well as indirect effects on equipment and its associated wiring located within the aircraft interior. This document applies to new aircraft and equipment designs, modifications of existing aircraft or equipment, and applications of existing (off the shelf) equipment on new aircraft. NOTE: This ARP does not address direct effects such as burning, eroding, blasting, of aircraft structure nor does it address fuel ignition hazards (see related reading material in 2.3 of this document). This ARP does not address lightning zoning methods or lightning test requirements, methods, and techniques.
CURRENT
2002-05-14
Standard
ARP5415A
This user's manual provides additional information and references relevant to identifying: (1) acceptance criteria for the indirect effects of lightning compliance approaches, (2) verification (analysis and test) methods including those associated with multiple stroke and multiple burst and (3) recommended design options to optimize needed system immunity to lightning indirect effects. Equipment hazards addressed include those due to the indirect effects on equipment mounted on the aircraft exterior and equipment located within the aircraft interior as well as all associated interconnecting wiring. This document has specific application toward those topics and subsystems addressed in ARP5413 but also provides additional guidelines in the application of those tests identified in DO-160/ED-14, Section 22.
HISTORICAL
2001-08-01
Standard
ARP5415
This user's manual provides additional information and references relevant to identifying: (1) acceptance criteria for the indirect effects of lightning compliance approaches, (2) verification (analysis and test) methods including those associated with multiple stroke and multiple burst and (3) recommended design options to optimize needed system immunity to lightning indirect effects. Equipment hazards addressed include those due to the indirect effects on equipment mounted on the aircraft exterior and equipment located within the aircraft interior as well as all associated interconnecting wiring. This document has specific application toward those topics and subsystems addressed in ARP5413 but also provides additional guidelines in the application of those tests identified in DO-160/ED-14, Section 22.
2012-02-06
WIP Standard
ARP5415B
This user's manual provides additional information and references relevant to identifying: (1) acceptance criteria for the indirect effects of lightning compliance approaches, (2) verification (analysis and test) methods including those associated with multiple stroke and multiple burst and (3) recommended design options to optimize needed system immunity to lightning indirect effects. Equipment hazards addressed include those due to the indirect effects on equipment mounted on the aircraft exterior and equipment located within the aircraft interior as well as all associated interconnecting wiring. This document has specific application toward those topics and subsystems addressed in ARP5413 but also provides additional guidelines in the application of those tests identified in DO- 160/ED-14, Section 22. This user's manual expands on the topics introduced in ARP5413, Certification of Aircraft Electrical/ Electronic Systems for the Indirect Effects of Lightning.
1989-10-01
WIP Standard
ARIR413A
This standard provides guidance to airframe manufacturers concerning the utilization of aircraft electrical power. This standard covers the description of basic power characteristics, and detailed guidance concerning transient protection, interference control, and equipment installation considerations.
1971-10-06
WIP Standard
ARIR421
This guidance standard was prepared in response to a need stated by air transport operators for uniformity in further subdividing the ATA Spec. 100 number system to better accommodate avionics systems. The ATA numbers are widely used in the maintenance community for inventory control, instruction manuals and equipment modification Service Bulletins.
HISTORICAL
2001-04-01
Standard
AMSH81200
This specification covers the heat treatment of titanium and titanium alloy products, including wrought and cast products, by material producers. This specification also covers furnace equipment requirements, test procedures, and general information for heat treating procedures, heat treating temperatures, and material test procedures for the heat treatment of titanium and titanium alloys. It also describes procedures which, when followd, have produced the desired properties within the limitations of the respective alloys.
HISTORICAL
2003-06-24
Standard
AMSH81200A
This specification covers the heat treatment of titanium and titanium alloy mill products (raw material), including wrought and cast products, by material producers. This specification also covers furnace equipment requirements, test procedures, and general information for heat treating procedures, heat treating temperatures, and material test procedures for the heat treatment of titanium and titanium alloys. It also describes procedures which, when followed, have produced the desired properties within the limitations of the respective alloys.
HISTORICAL
2008-11-11
Standard
AMSH81200B
This specification covers the heat treatment of titanium and titanium alloy mill products (raw material), including wrought and cast products, by material producers. This specification also covers furnace equipment requirements, test procedures, and general information for heat treating procedures, heat treating temperatures, and material test procedures for the heat treatment of titanium and titanium alloys. It also describes procedures that, when followed, have produced the desired properties within the limitations of the respective alloys.
HISTORICAL
2010-02-24
Standard
AMSH81200C
This specification covers the heat treatment of titanium and titanium alloy mill products (raw material), including wrought and cast products, by material producers. This specification also covers furnace equipment requirements, test procedures, and general information for heat treating procedures, heat treating temperatures, and material test procedures for the heat treatment of titanium and titanium alloys. It also describes procedures that, when followed, have produced the desired properties within the limitations of the respective alloys.
2017-09-22
WIP Standard
AMSH81200E
This specification covers the heat treatment of titanium and titanium alloy mill products (raw material), including wrought and cast products, by material producers. This specification also covers furnace equipment requirements, test procedures, and general information for heat treating procedures, heat treating temperatures, and material test procedures for the heat treatment of titanium and titanium alloys. It also describes procedures that, when followed, have produced the desired properties within the limitations of the respective alloys.
CURRENT
2014-07-23
Standard
AMSH81200D
This specification covers the heat treatment of titanium and titanium alloy mill products (raw material), including wrought and cast products, by material producers. This specification also covers furnace equipment requirements, test procedures, and general information for heat treating procedures, heat treating temperatures, and material test procedures for the heat treatment of titanium and titanium alloys. It also describes procedures that, when followed, have produced the desired properties within the limitations of the respective alloys.
HISTORICAL
2000-09-01
Standard
AS9101
The purpose of this procedure is to define the content and the presentation of the Assessment Report. PLEASE NOTE: This downloadable version of the AS9101 checklist features the ability to edit the form electronically. In order to save your changes, however, you will need to have either the full version of Adobe Acrobat (not just Acrobat Reader) or Adobe Approval. About the AS9100 Family of Standards This standard, AS9101, is the checklist corresponding to AS9100, issued in November 1999. AS9101A, issued in April 2002, is the checklist corresponding to AS9100A, issued in August 2001.