Criteria

Text:
Content:
Display:

Results

Viewing 271 to 300 of 9577
HISTORICAL
1992-10-01
Standard
J1591_199210
This SAE Standard specifies the general characteristics of piston rings and individual dimensional criteria, which are specified as appropriate in the documents in Section 2. This document also provides a system for coding, designation, and marking of piston rings. This document applies to the manufacture of piston rings up to and including 200 mm diameter for reciprocating internal combustion engines. It also applies to piston rings for compressors working under similar conditions.
HISTORICAL
1998-04-01
Standard
J1589_199804
Differences, where they exist, are shown in Appendix A. This SAE Standard defines the measuring principles to be used for measuring piston rings. It applies to piston rings up to and including 200 mm diameter for reciprocating combustion engines. These inspection measuring principles may also be used for piston rings for compressors working under analogous conditions.
CURRENT
2008-06-30
Standard
J1589_200806
Differences, where they exist, are shown in Appendix A. This SAE Standard defines the measuring principles to be used for measuring piston rings. It applies to piston rings up to and including 200 mm diameter for reciprocating combustion engines. These inspection measuring principles may also be used for piston rings for compressors working under analogous conditions.
CURRENT
2008-06-30
Standard
J1588_200806
Differences, where they exist, are shown in Appendix A with associated rationale. This SAE Standard defines the most commonly used terms for piston rings. These terms designate either types of piston rings or certain characteristics and phenomena of piston rings. The terms and definitions apply to piston rings for reciprocating internal combustion engines and compressors working under analogous conditions. Appendix B is included which lists equivalent terms in English, French, Russian, German, Spanish, Portuguese, Italian, and Japanese.
HISTORICAL
1990-01-01
Standard
J1589_199001
Differences, where they exist, are shown in Appendix A. This SAE Standard defines the measuring principles to be used for measuring piston rings. It applies to piston rings up to and including 200 mm diameter for reciprocating combustion engines. These inspection measuring principles may also be used for piston rings for compressors working under analogous conditions.
HISTORICAL
1990-09-01
Standard
J1588_199009
Differences, where they exist, are shown in Appendix A with associated rationale. This SAE Standard defines the most commonly used terms for piston rings. These terms designate either types of piston rings or certain characteristics and phenomena of piston rings. The terms and definitions apply to piston rings for reciprocating internal combustion engines and compressors working under analogous conditions. Appendix B is included which lists equivalent terms in English, French, Russian, German, Spanish, Portuguese, Italian, and Japanese.
HISTORICAL
1998-04-01
Standard
J1588_199804
Differences, where they exist, are shown in Appendix A with associated rationale. This SAE Standard defines the most commonly used terms for piston rings. These terms designate either types of piston rings or certain characteristics and phenomena of piston rings. The terms and definitions apply to piston rings for reciprocating internal combustion engines and compressors working under analogous conditions. Appendix B is included which lists equivalent terms in English, French, Russian, German, Spanish, Portuguese, Italian, and Japanese.
HISTORICAL
1992-10-01
Standard
J1588_199210
Differences, where they exist, are shown in Appendix A with associated rationale. This SAE Standard defines the most commonly used terms for piston rings. These terms designate either types of piston rings or certain characteristics and phenomena of piston rings. The terms and definitions apply to piston rings for reciprocating internal combustion engines and compressors working under analogous conditions. Appendix B is included which lists equivalent terms in English, French, Russian, German, Spanish, Portuguese, Italian, and Japanese.
HISTORICAL
1990-03-16
Standard
J1583_199003
The scope of this specification is to define the transfer layer and the consequences of the Controller Area Network (CAN) protocol on the surrounding layers.
CURRENT
1999-07-15
Standard
J1583_199907
The scope of this specification is to define the transfer layer and the consequences of the Controller Area Network (CAN) protocol on the surrounding layers.
CURRENT
2014-10-24
Standard
J1579_201410
These requirements define minimum recommended levels of side stand retraction performance of a new side stand/motorcycle combination when tested according to the procedures of SAE J1578.
CURRENT
2011-10-27
Standard
J1580_201110
this document is to be used on cutting edges and end bits in conjunction with metric bolts (reference ISO 7852-1982) typically used on off-road, self-propelled work machines as described in SAE J1116. The cutting edges are further defined in SAE J737, J739, J1304, and J1581. The end bits are further defined in SAE J63.
HISTORICAL
1989-12-01
Standard
J1580_198912
This document is to be used on cutting edges and end bits in conjunction with metric bolts (Reference ISO 7852-1982) typically used on off-road, self-propelled work machines as described in SAE J1116. The cutting edges are further defined in SAE J737, J739, J1304, and J1581. The end bits are futher defined in SAE J63. This document specifies the principle shapes and dimensions for countersunk square holes.
HISTORICAL
1997-07-01
Standard
J1578_199707
This test procedure provides a standard method for evaluating the side stand retraction performance of a side stand/motorcycle combination. This test procedure applies to any two-wheeled motorcycle without a sidecar, equipped with a side stand, and intended for highway use. (See SAE J213.) This SAE Recommended Practice is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering the use of this document.
HISTORICAL
2003-08-29
Standard
J1578_200308
This test procedure provides a standard method for evaluating the side stand retraction performance of a side stand/motorcycle combination. This test procedure applies to any two-wheeled motorcycle without a sidecar, equipped with a side stand, and intended for highway use. (See SAE J213.) This SAE Recommended Practice is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering the use of this document.
CURRENT
2014-10-24
Standard
J1578_201410
This test procedure provides a standard method for evaluating the side stand retraction performance of a side stand/motorcycle combination.
HISTORICAL
2009-01-27
Standard
J1578_200901
This test procedure provides a standard method for evaluating the side stand retraction performance of a side stand/motorcycle combination. This test procedure applies to any two-wheeled motorcycle without a sidecar, equipped with a side stand, and intended for highway use. (See SAE J213.) This SAE Recommended Practice is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering the use of this document.
HISTORICAL
1998-04-01
Standard
J1579_199804
These requirements define minimum recommended levels of side stand retraction performance of a new side stand/motorcycle combination when tested according to the procedures of SAE J1578. These requirements apply to any new two-wheeled motorcycle without a sidecar, equipped with a side stand, and intended for highway use. (See SAE J213). This SAE Recommended Practice is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering use of this document.
HISTORICAL
2003-05-30
Standard
J1579_200305
These requirements define minimum recommended levels of side stand retraction performance of a new side stand/motorcycle combination when tested according to the procedures of SAE J1578. These requirements apply to any new two-wheeled motorcycle without a sidecar, equipped with a side stand, and intended for highway use. (See SAE J213). This SAE Recommended Practice is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering use of this document.
HISTORICAL
2009-01-27
Standard
J1579_200901
These requirements define minimum recommended levels of side stand retraction performance of a new side stand/motorcycle combination when tested according to the procedures of SAE J1578. These requirements apply to any new two-wheeled motorcycle without a sidecar, equipped with a side stand, and intended for highway use. (See SAE J213). This SAE Recommended Practice is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering use of this document.
HISTORICAL
1990-06-01
Standard
J1946_199006
This SAE Standard specifies the nominal dimensions and tolerances which affect the interchangeability between companion flanges and mating parts. The flanges covered by this document are designated type A and type S. The type A flanges are equivalent to type A ISO 7646. The type S flanges are equivalent to the type S ISO 7647. Type A is an external (male) pilot construction and type S is an internal (female) pilot construction. These flanges are not interchangeable. Dimensions not specified are left to the discretion of the component manufacturer.
CURRENT
2004-08-20
Standard
J1941_200408
This SAE Recommended Practice applies to engine coolant concentrate, low silicate ethylene glycol base, for use in cooling systems of heavy-duty engines. An initial charge of supplemental coolant additive (SCA) is required when using this type of coolant concentrate.
HISTORICAL
1990-04-01
Standard
J1941_199004
This SAE Recommended Practice applies to engine coolant concentrate, low silicate ethylene glycol base, for use in cooling systems of heavy-duty engines. An initial charge of supplemental coolant additive (SCA) is required when using this type of coolant concentrate.
CURRENT
2016-04-05
Standard
J1959_201604
This specification covers underbody corrosion preventive compounds for application to vehicle underbodies.
HISTORICAL
2003-09-25
Standard
J1959_200309
This specification covers underbody corrosion preventive compounds for application to vehicle underbodies.
HISTORICAL
1989-06-01
Standard
J1959_198906
This specification covers underbody corrosion preventive compounds for application to vehicle underbodies. This document contains reference to certain automotive industry tests, it only reflects interest in selecting what is felt to be the easiest and most useful tests for evaluation of rust corrosion preventatives, and does not suggest that the tests of other vehicle manufacturers are of lesser value or validity.
2016-04-13
WIP Standard
J1961
This test method specifies the operating procedures for using a solar fresnel reflector apparatus for the accelerated exposure of various automotive materials. Sample preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
CURRENT
2011-05-16
Standard
J1961_201105
This test method specifies the operating procedures for using a solar fresnel reflector apparatus for the accelerated exposure of various automotive materials.
HISTORICAL
2002-03-22
Standard
J1961_200203
This test method specifies the operating procedures for using a solar fresnel reflector apparatus for the accelerated exposure of various automotive materials. Sample preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
HISTORICAL
1988-12-01
Standard
J1961_198812
This test method specifies the operating procedures for using a solar fresnel reflector apparatus for the accelerated exposure of various automotive materials. Sample preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
Viewing 271 to 300 of 9577