Criteria

Text:
Content:
Display:

Results

Viewing 181 to 210 of 9577
CURRENT
2007-10-08
Standard
USCAR35
A bolt-load retention (BLR) test is a practical test to determine the bolt load of a fastener joint with time and at given temperatures. There are three types of BLR tests described in this standard, namely general-purpose test, design-purpose test, and screening material test. A general-purpose BLR test may be used for screening materials, while a design-purpose BLR test is usually used to verify the BLR behavior of a specific joint. The screening material test is an example of the general-purpose test for typical automotive applications.
CURRENT
2007-03-13
Standard
USCAR32
This standard lists variables that shall be investigated and reported as an initial investigation into new or revised surface finishes intended for use on fasteners. This standard provides instruction for producing a final report that will be used to determine if further investigation of a surface finish is justified. Further investigation may include tests and evaluations specific to an individual OEM prior to introduction/approval of the surface finish. The final report shall include the results, observations, and conclusions for all of the variables. The final report may be made up of several individual reports covering each variable. In all cases the laboratory performing the test, the test date and the report approver shall be included in the final report.
CURRENT
2010-01-15
Standard
USCAR3-3
The procedures contained in this specification cover the laboratory testing of miniature incandescent bulbs for use in automotive illumination and signaling applications. The following tests shall be run whenever the following occurs: New bulb design Design or process change made to an existing bulb, which could affect the outcome of the test. The completion of one calendar year as noted in the following Test Schedule Table. Process control data is acceptable.
HISTORICAL
1997-07-01
Standard
USCAR3
HISTORICAL
2002-04-15
Standard
USCAR3-2
The procedures contained in this specification cover the laboratory testing of miniature incandescent bulbs for use in automotive illumination and signaling applications.
CURRENT
2007-10-08
Standard
USCAR27
This specification is a general level subsystem light source specification that establishes test requirements of a Gas Discharge Light Source (GDLS) subsystem for use on passenger vehicles. The completed test data to this test specification is intended to be provided to the OEM by the Tier one lamp set maker as part of the lamp assembly PPAP. Re-testing shall be required if any portion of the approved GDLS experiences a design, manufacturing or component change. This document shall be applied to systems that meet the requirements for design, performance and validation established by government standards. The subsystem is defined as the ballast, igniter and light source and shall be tested as a subsystem and considered one test sample for the entire test sequence. A failure of any component in the test sample shall constitute a failure of the entire sample. Substitution or replacement of only the light source shall be allowed during testing.
HISTORICAL
1973-03-01
Standard
J1003_197303
This SAE Recommended Practice is intended for use as a test procedure to determine the gaseous emission level of diesel engines. Its purpose is to provide a map of an engine's emissions characteristics which, through use of the proper weighing factors, can be used as a measure of that engine's emission levels under various applications. The emission results for hydrocarbons, nitrogen oxides, carbon monoxide, and carbon dioxide are expressed in units of grams per kilowatt hour (grams/brake horsepower hour) and represent the mass rate of emissions per unit of work accomplished. The emissions are measured in accordance with SAE Recommended Practices J177, J215, and J244 using nondispersive infrared equipment for CO and CO2, a heated flame ionization analyzer for HC, and a high performance NDIR or a chemiluminescence analyzer for NO{sub}x. All emissions are measured during steady-state engine operation.
HISTORICAL
1990-06-01
Standard
J1003_199006
This SAE Recommended Practice is intended for use as a test procedure to determine the gaseous emission level of diesel engines. Its purpose is to provide a map of an engine's emissions characteristics which, through use of the proper weighing factors, can be used as a measure of that engine's emission levels under various applications. The emission results for hydrocarbons, nitrogen oxides, carbon monoxide, and carbon dioxide are expressed in units of grams per kilowatt hour (grams/brake horsepower hour) and represent the mass rate of emissions per unit of work accomplished. The emissions are measured in accordance with SAE Recommended Practices J177, J215, and J244 using nondispersive infrared equipment for CO and CO2, a heated flame ionization analyzer for HC, and a high performance NDIR or a chemiluminescence analyzer for NO{sub}x. All emissions are measured during steady-state engine operation.
HISTORICAL
1984-02-01
Standard
J1003_198402
This SAE Recommended Practice is intended for use as a test procedure to determine the gaseous emission level of diesel engines. Its purpose is to provide a map of an engine's emissions characteristics which, through use of the proper weighing factors, can be used as a measure of that engine's emission levels under various applications. The emission results for hydrocarbons, nitrogen oxides, carbon monoxide, and carbon dioxide are expressed in units of grams per kilowatt hour (grams/brake horsepower hour) and represent the mass rate of emissions per unit of work accomplished. The emissions are measured in accordance with SAE Recommended Practices J177, J215, and J244 using nondispersive infrared equipment for CO and CO2, a heated flame ionization analyzer for HC, and a high performance NDIR or a chemiluminescence analyzer for NO{sub}x. All emissions are measured during steady-state engine operation.
CURRENT
2002-10-21
Standard
J1003_200210
This SAE Recommended Practice is intended for use as a test procedure to determine the gaseous emission level of diesel engines. Its purpose is to provide a map of an engine's emissions characteristics which, through use of the proper weighing factors, can be used as a measure of that engine's emission levels under various applications. The emission results for hydrocarbons, nitrogen oxides, carbon monoxide, and carbon dioxide are expressed in units of grams per kilowatt hour (grams/brake horsepower hour) and represent the mass rate of emissions per unit of work accomplished. The emissions are measured in accordance with SAE Recommended Practices J177, J215, and J244 using nondispersive infrared equipment for CO and CO2, a heated flame ionization analyzer for HC, and a high performance NDIR or a chemiluminescence analyzer for NO{sub}x. All emissions are measured during steady-state engine operation.
HISTORICAL
1995-06-01
Standard
J1003_199506
This SAE Recommended Practice is intended for use as a test procedure to determine the gaseous emission level of diesel engines. Its purpose is to provide a map of an engine's emissions characteristics which, through use of the proper weighing factors, can be used as a measure of that engine's emission levels under various applications. The emission results for hydrocarbons, nitrogen oxides, carbon monoxide, and carbon dioxide are expressed in units of grams per kilowatt hour (grams/brake horsepower hour) and represent the mass rate of emissions per unit of work accomplished. The emissions are measured in accordance with SAE Recommended practices J177, J215, and J244 using nondispersive infrared equipment for CO and CO2, a heated flame ionization analyzer for HC, and a high performance NDIR or a chemiluminescence analyzer for NOx. All emissions are measured during steady-state engine operation.
CURRENT
2007-11-20
Standard
J1013_200711
This SAE Standard defines a method for the measurement of the whole body vibration to which the seated operator of off-highway self-propelled work machines is exposed while performing an actual or simulated operation. It applies to vibration transmitted to the operator through the seat. There are not equivalent ISO Standards. In the main body of this document, conditions are defined for measuring and recording whole body vibration of the seated operator of off-highway self-propelled work machines. The specification of instruments, analytic methods, and description of site and operating conditions allows the measurements to be made and reported with an acceptable precision. The procedure includes means of weighing the vibration level at different frequencies as specified in ISO2631. A standard format for reporting spectral data is recommended. The definitions, instruments, and analytic methods also apply to simulated tests for operator vibration as performed in laboratories.
HISTORICAL
1992-08-01
Standard
J1013_199208
This SAE Standard defines a method for the measurement of the whole body vibration to which the seated operator of off-highway self-propelled work machines is exposed while performing an actual or simulated operation. It applies to vibration transmitted to the operator through the seat. There are not equivalent ISO Standards. In the main body of this document, conditions are defined for measuring and recording whole body vibration of the seated operator of off-highway self-propelled work machines. The specification of instruments, analytic methods, and description of site and operating conditions allows the measurements to be made and reported with an acceptable precision. The procedure includes means of weighing the vibration level at different frequencies as specified in ISO2631. A standard format for reporting spectral data is recommended. The definitions, instruments, and analytic methods also apply to simulated tests for operator vibration as performed in laboratories.
HISTORICAL
1980-01-01
Standard
J1013_198001
This SAE Standard defines a method for the measurement of the whole body vibration to which the seated operator of off-highway self-propelled work machines is exposed while performing an actual or simulated operation. It applies to vibration transmitted to the operator through the seat. There are not equivalent ISO Standards. In the main body of this document, conditions are defined for measuring and recording whole body vibration of the seated operator of off-highway self-propelled work machines. The specification of instruments, analytic methods, and description of site and operating conditions allows the measurements to be made and reported with an acceptable precision. The procedure includes means of weighing the vibration level at different frequencies as specified in ISO2631. A standard format for reporting spectral data is recommended. The definitions, instruments, and analytic methods also apply to simulated tests for operator vibration as performed in laboratories.
HISTORICAL
2000-10-09
Standard
J1900_200010
Bond, as it relates to elastomeric seals, is defined as "The adhesion, established by vulcanization, between two cured elastomeric surfaces, or between one cured elastomeric surface and one nonelastomeric surface." Vulcanization refers in this case to chemical bonding. Good bond is essential to the function of elastomeric radial lip seals and other precision bonded parts. This SAE Recommended Practice describes a universal bond test fixture developed by the RMA that can be mounted to a conventional tensile test machine. This will allow a quantitative evaluation of bond rather than a merely qualitative one.
HISTORICAL
1990-10-01
Standard
J1900_199010
Bond, as it relates to elastomeric seals, is defined as "The adhesion, established by vulcanization, between two cured elastomeric surfaces, or between one cured elastomeric surface and one nonelastomeric surface." Vulcanization refers in this case to chemical bonding. Good bond is essential to the function of elastomeric radial lip seals and other precision bonded parts. This SAE Recommended Practice describes a universal bond test fixture developed by the RMA that can be mounted to a conventional tensile test machine. This will allow a quantitative evaluation of bond rather than a merely qualitative one.
HISTORICAL
1998-09-01
Standard
J1892_199809
This SAE Recommended Practice describes the basic content requirements, bar-code specifications, and functional test specifications of a vehicle emission configuration (VEC) label. On the vehicle, the VEC label is to be mounted under the hood in a readily accessible location for use of a bar-code scanning device. This document specifies a permanent vehicle emission configuration label that can be automatically identified through a bar-coded format.
CURRENT
2014-06-16
Standard
J1892_201406
This SAE Recommended Practice describes the basic content requirements, bar-code specifications, and functional test specifications of a vehicle emission configuration (VEC) label. On the vehicle, the VEC label is to be mounted under the hood in a readily accessible location for use of a bar-code scanning device. This document specifies a permanent vehicle emission configuration label that can be automatically identified through a bar-coded format.
HISTORICAL
1993-10-29
Standard
J1892_199310
This SAE Recommended Practice describes the basic content requirements, bar-code specifications, and functional test specifications of a vehicle emission configuration (VEC) label. On the vehicle, the VEC label is to be mounted under the hood in a readily accessible location for use of a bar-code scanning device. This document specifies a permanent vehicle emission configuration label that can be automatically identified through a bar-coded format.
CURRENT
2017-02-09
Standard
J1883_201702
The bushing "TRAC" code is intended to be a tool that will aid in the definition of the geometric environment for the test, or use, of an elastomeric bushing.
HISTORICAL
1994-10-01
Standard
J1883_199410
The bushing "TRAC" code is intended to be a tool that will aid in the definition of the geometric environment for the test, or use, of an elastomeric bushing.
HISTORICAL
1988-03-01
Standard
J1883_198803
The bushing 'TRAC' code is intended to be a tool that will aid in the definition of the geometric environment for the test, or use, of an elastomeric bushing.
CURRENT
2001-11-15
Standard
J1649/1_200111
This part of SAE J1649/1 specifies quality classes of industrial compressed air for general use (e.g. for workshops, the construction industry, pneumatic transport, etc.) without consideration of the quality of the air when it is discharged from the compressor. The quality class of compressed air for a particular application has to be based on the mean value of several measurements carried out over a specific period of time and under defined operating conditions.
CURRENT
2011-04-01
Standard
J1657_201104
The purpose of this SAE Recommended Practice is to provide criteria for determining the acceptability of candidate retrofit refrigerants to replace CFC-12 (R-12) in mobile A/C systems originally designed to use CFC-12 (R-12).
CURRENT
1996-08-01
Standard
J1655_199608
This SAE Information Report is intended to help promote the proper use of Predictive and Preventive Diagnostic Maintenance in hydraulic systems. This document can be used as a selection guide for the level of diagnostic equipment and methods to specify for a given application. Each application has its own particular requirements.
HISTORICAL
1999-02-01
Standard
J1657_199902
The purpose of this SAE Recommended Practice is to provide criteria for determining the acceptability of candidate retrofit refrigerants to replace CFC-12 (R-12) in mobile A/C systems originally designed to use CFC-12 (R-12).
CURRENT
1995-08-01
Standard
J1663_199508
This SAE Standard is a truth-in-labeling standard for map databases.
HISTORICAL
1999-02-01
Standard
J1659_199902
The purpose of this SAE Recommended Practice is to establish the specific criteria for the selection of a replacement refrigerant for mobile CFC-12 (R-12) air-conditioning (A/C) systems. This document provides guidelines for qualifying candidate refrigerant. The requirements include laboratory and field testing. The alternate refrigerant shall provide comparable system performance as CFC-12 (R-12) as defined herein. The vehicle testing shall be conducted on representative vehicle manufacturer's product line, in which the refrigerant is intended to be used, such as cycling clutch orifice tube, constant run orifice tube, cycling clutch expansion valve, or continuous run expansion valve refrigerant system. This document is complete only when combined with the requirements of SAE J1657.
Viewing 181 to 210 of 9577