Refine Your Search

Search Results

Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2016-11-18
CURRENT
J1102M_201611
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: Nonserrated shank bolts which are heat treated Serrated shank bolts which are case hardened
Standard

Accelerated Exposure of Automotive Interior Trim Material Using Outdoor Under-Glass Controlled Sun-Tracking Temperature and Humidity Apparatus

2016-03-23
WIP
J2230
This SAE Standard specifies operating procedure for the exposure of automotive interior trim materials in an outdoor behind-glass apparatus in which the temperature is controlled in a 24 h cycle. The humidity is controlled during the dark (night) portion of the cycle. Specimen preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
Standard

Fiberboard Test Procedure

2010-03-02
CURRENT
J315_201003
This SAE Standard provides test methods for determining the critical characteristics of basic or finished fiberboard products. Where applicable, methods of test developed by SAE and ASTM have been referenced.
Standard

Fiberboard Test Procedure

2004-09-20
HISTORICAL
J315_200409
This SAE Standard provides test methods for determining the critical characteristics of basic or finished fiberboard products. Where applicable, methods of test developed by SAE and ASTM have been referenced.
Standard

Drain, Fill, and Level Plugs for Off-Road, Self-Propelled Work Machines

1978-03-01
HISTORICAL
J371A_197803
This SAE Recommended Practice applies to off-road, self-propelled work machines as defined in SAE J1116, Categories 1, 2, 4, and 5. Plugs are extensively used in off-road, self-propelled work machines as defined in SAE J1116. Loss of these plugs, stripping of the threads, or failure to tighten because of difficulty in finding the right tool can result in serious damage and/or increased down time. All the plugs listed are nominal inch sizes pending the development of metric plug standards. The purpose of this document is to standardize and, therefore, minimize the number of sizes and types of drain, fill, and level plugs required. It also establishes types and sizes of pipe thread and straight thread plugs requiring commercially available hand tools for removal and installation. It is not intended to establish dimensions and materials.
Standard

Fiberboard Test Procedure

2016-03-29
WIP
J315
This SAE Standard provides test methods for determining the critical characteristics of basic or finished fiberboard products. Where applicable, methods of test developed by SAE and ASTM have been referenced.
Standard

Drain, Fill, and Level Plugs for Off-Road, Self-Propelled Work Machines

1985-07-01
HISTORICAL
J371_198507
This SAE Recommended Practice applies to off-road, self-propelled work machines as defined in SAE J1116, Categories 1, 2, 4, and 5. Plugs are extensively used in off-road, self-propelled work machines as defined in SAE J1116. Loss of these plugs, stripping of the threads, or failure to tighten because of difficulty in finding the right tool can result in serious damage and/or increased down time. All the plugs listed are nominal inch sizes pending the development of metric plug standards. The purpose of this document is to standardize and, therefore, minimize the number of sizes and types of drain, fill, and level plugs required. It also establishes types and sizes of pipe thread and straight thread plugs requiring commercially available hand tools for removal and installation. It is not intended to establish dimensions and materials.
Standard

Fiberboard Test Procedure

1980-09-01
HISTORICAL
J315_198009
This SAE Standard provides test methods for determining the critical characteristics of basic or finished fiberboard products. Where applicable, methods of test developed by SAE and ASTM have been referenced.
Standard

Fiberboard Test Procedure

1985-01-01
HISTORICAL
J315_198501
This SAE Standard provides test methods for determining the critical characteristics of basic or finished fiberboard products. Where applicable, methods of test developed by SAE and ASTM have been referenced.
Standard

Drain, Fill, and Level Plugs for Off-Road, Self-Propelled Work Machines

2006-06-05
HISTORICAL
J371_200606
This SAE Recommended Practice applies to off-road, self-propelled work machines as defined in SAE J1116, Categories 1, 2, 4, and 5. Plugs are extensively used in off-road, self-propelled work machines as defined in SAE J1116. Loss of these plugs, stripping of the threads, or failure to tighten because of difficulty in finding the right tool can result in serious damage and/or increased down time. All the plugs listed are nominal inch sizes pending the development of metric plug standards. The purpose of this document is to standardize and, therefore, minimize the number of sizes and types of drain, fill, and level plugs required. It also establishes types and sizes of pipe thread and straight thread plugs requiring commercially available hand tools for removal and installation. It is not intended to establish dimensions and materials.
Standard

Drain, Fill, and Level Plugs for Off-Road, Self-Propelled Work Machines

1993-05-01
HISTORICAL
J371_199305
This SAE Recommended Practice applies to off-road, self-propelled work machines as defined in SAE J1116, Categories 1, 2, 4, and 5. Plugs are extensively used in off-road, self-propelled work machines as defined in SAE J1116. Loss of these plugs, stripping of the threads, or failure to tighten because of difficulty in finding the right tool can result in serious damage and/or increased down time. All the plugs listed are nominal inch sizes pending the development of metric plug standards. The purpose of this document is to standardize and, therefore, minimize the number of sizes and types of drain, fill, and level plugs required. It also establishes types and sizes of pipe thread and straight thread plugs requiring commercially available hand tools for removal and installation. It is not intended to establish dimensions and materials.
X