Refine Your Search

Search Results

Standard

A Tilt Table Procedure for Measuring the Static Rollover Threshold for Heavy Trucks

2011-05-17
CURRENT
J2180_201105
The test procedure applies to roll coupled units such as straight trucks, tractor semitrailers, full trailers, B-trains, etc. The test is aimed at evaluating the level of lateral acceleration required to rollover a vehicle or a roll-coupled unit of a vehicle in a steady turning situation. Transient, vibratory, or dynamic rollover situations are not simulated by this test. Furthermore, the accuracy of the test decreases as the tilt angle increases, although this is a small effect at the levels of tilt angle used in testing heavy trucks. The test accuracy is accepted for vehicles that will rollover at lateral acceleration levels below 0.5 g corresponding to a tilt table angle of less than approximately 27 degrees. Even so, the results for heavy trucks with rollover thresholds greater than 0.5 g could be used for comparing their relative static roll stability.
Standard

A Tilt Table Procedure for Measuring the Static Rollover Threshold for Heavy Trucks

1998-12-01
HISTORICAL
J2180_199812
The test procedure applies to roll coupled units such as straight trucks, tractor semitrailers, full trailers, B-trains, etc. The test is aimed at evaluating the level of lateral acceleration required to rollover a vehicle or a roll-coupled unit of a vehicle in a steady turning situation. Transient, vibratory, or dynamic rollover situations are not simulated by this test. Furthermore, the accuracy of the test decreases as the tilt angle increases, although this is a small effect at the levels of tilt angle used in testing heavy trucks. The test accuracy is accepted for vehicles that will rollover at lateral acceleration levels below 0.5 g corresponding to a tilt table angle of less than approximately 27 degrees. Even so, the results for heavy trucks with rollover thresholds greater than 0.5 g could be used for comparing their relative static roll stability.
Standard

Logistics Product Data Reports Handbook

2015-10-21
WIP
TAHB0007_1A
This document describes a set of standardized reports that can be generated using the logistics product data elements contained in GEIA-STD-0007-B. Each report is defined by selection options, processing, format, report sequence, and data sources. The selection options paragraph identifies recommended mandatory and optional selections that can be made by the user to tailor the report content. The processing paragraph identifies qualifying criteria for report data, report calculations, and specific instructions regarding how the data should be presented on the report. Each report has a sample report showing its format. Report sequences specify the sort criteria for a given report, and each Part/Section within a report. There is an attached listing of data sources for the elements that are on a report. The listing provides the report header for each element; and its GEIA-STD-0007-B data element/attribute along with the appropriate entity.
Standard

Logistics Product Data Reports Handbook

2013-05-01
CURRENT
TAHB0007_1
This document describes a set of standardized reports that can be generated using the logistics product data elements contained in GEIA-STD-0007-B. Each report is defined by selection options, processing, format, report sequence, and data sources. The selection options paragraph identifies recommended mandatory and optional selections that can be made by the user to tailor the report content. The processing paragraph identifies qualifying criteria for report data, report calculations, and specific instructions regarding how the data should be presented on the report. Each report has a sample report showing its format. Report sequences specify the sort criteria for a given report, and each Part/Section within a report. There is an attached listing of data sources for the elements that are on a report. The listing provides the report header for each element; and its GEIA-STD-0007-B data element/attribute along with the appropriate entity.
Standard

Rear Wheel Splash and Stone Throw Protection

2002-08-23
HISTORICAL
J682_200208
For guidance only in regard to highway commercial motor vehicles where protection to the rear against rear wheel splash and stone throw is deemed necessary, the following clearance specifications are recommended.
Standard

Wheel Mounting Elements for Industrial and Agricultural Disc Wheels

1986-06-01
HISTORICAL
J714_198606
This SAE Recommended Practice includes wheel mounting elements subject to standardization in a series of industrial and agricultural disc wheels. The disc may be reversible or nonreversible and concave or convex (See Figure 1 and Table 1).
Standard

Vehicle Electromagnetic Immunity--On-Board Transmitter Simulation

2009-08-03
CURRENT
J551/12_200908
This part of SAE J551 specifies on-board transmitter simulation test methods and procedures for testing passenger cars and commercial vehicles. The electromagnetic disturbances considered in this part of SAE J551 are limited to continuous narrow band electromagnetic fields. SAE J551/1 specifies general, definitions, practical use, and basic principles of the test procedure.
Standard

Marine Stern Drive and Inboard Spark-Ignition Engine On-Board Diagnostics Implementation Guide

2012-04-13
HISTORICAL
J1939/5_201204
This document describes the application of the SAE J1939 recommended practices for compliance with on-board diagnostic malfunction detection system requirements for marine sterndrive and inboard spark ignition engines, as mandated by the California Air Resources Board (CARB). These Otto-cycle engines are not derived from automotive diesel-cycle engines.
Standard

Marine Stern Drive and Inboard Spark-Ignition Engine On-Board Diagnostics Implementation Guide

2008-02-21
HISTORICAL
J1939/5_200802
This document describes the application of the SAE J1939 recommended practices for compliance with on-board diagnostic malfunction detection system requirements for marine sterndrive and inboard spark ignition engines, as mandated by the California Air Resources Board (CARB). These Otto-cycle engines are not derived from automotive diesel-cycle engines.
Standard

Marine Stern Drive and Inboard Spark-Ignition Engine On-Board Diagnostics Implementation Guide

2017-10-13
CURRENT
J1939/5_201710
This document describes the application of the SAE J1939 recommended practices for compliance with on-board diagnostic malfunction detection system requirements for marine sterndrive and inboard spark ignition engines, as mandated by the California Air Resources Board (CARB). These Otto-cycle engines are not derived from automotive diesel-cycle engines.
Standard

Primary Single Phase Nominal 120 VAC Wiring Distribution Assembly Design - Truck and Bus

2008-01-14
HISTORICAL
J2698_200801
1.1 This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase nominal 120 VAC circuits that provide power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off. The power supply comes from alternative sources such as land-based grid power, DC-AC inverters and auxiliary power generators. The circuits may also provide power to improve vehicle performance through charging batteries or operating cold-weather starting aids. 1.2 This document is not intended to provide guidance for electric or hybrid electric vehicle wiring circuits. Refer to SAE J1673 for high voltage automotive wiring assembly design. 1.3 Engine block heaters are 120 VAC devices that are used on a multitude of vehicle platforms in addition to trucks with sleeper cabs. Generally, the engine block heater circuit is wired independent of hotel loads.
Standard

Primary Single Phase Nominal 120 VAC Wiring Distribution Assembly Design—Truck and Bus

2018-10-04
CURRENT
J2698_201810
This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase nominal 120 VAC circuits that provide power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off. The power supply comes from alternative sources such as land-based grid power, DC-AC inverters and auxiliary power generators. The circuits may also provide power to improve vehicle performance through charging batteries or operating cold-weather starting aids.
Standard

Primary Single Phase Nominal 120 VAC Wiring Distribution Assembly Design—Truck and Bus

2014-11-24
HISTORICAL
J2698_201411
This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase nominal 120 VAC circuits that provide power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off. The power supply comes from alternative sources such as land-based grid power, DC-AC inverters and auxiliary power generators. The circuits may also provide power to improve vehicle performance through charging batteries or operating cold-weather starting aids.
Standard

Cartridge Cavity

2018-10-30
CURRENT
J2494/4_201810
This SAE Standard covers complete general and dimensional data for the manufacture of, T6061-T6 Aluminum cavities designed to receive Push To Connect threadless fittings known as “cartridges“, for air brake applications. This document is not intended to specify or recommend any style or manufacture of such cartridges but to establish uniform cavity dimensions for interchangeability purposes.
Standard

Cartridge Cavity

2011-10-28
HISTORICAL
J2494/4_201110
This SAE Standard covers complete general and dimensional data for the manufacture of, T6061-T6 Aluminum cavities designed to receive Push To Connect threadless fittings known as “cartridges“, for air brake applications. This document is not intended to specify or recommend any style or manufacture of such cartridges but to establish uniform cavity dimensions for interchangeability purposes.
Standard

R134a Refrigerant Charge Determination Test Method

2018-09-11
CURRENT
J3023_201809
The purpose of this document is to establish guidelines for determining the critical R134a refrigerant charge for off-road, self-propelled work machines as defined in SAE J1116 and Agricultural Tractors as defined in ANSI/ASAE S390. It will develop a minimum to maximum refrigerant charge range in which the HVAC system can maintain proper operation. Operating conditions and characteristics of the equipment will influence the optimum charge. Since these conditions and characteristics vary greatly from one application to another, careful consideration should be taken to determine the optimum R134a refrigerant charge for the HVAC system.
Standard

Heavy Duty OBD IUMPR Data Collection Tool Process

2018-09-04
CURRENT
J3162_201809
This document describes the collection of IUMPR data required by the Heavy Duty On-Board Diagnostic regulation 13 CCR 1971.1 (l)(2.3.3), using SAE J1939-defined messages incorporated in a suite of software functions.
X