SAE Technical Standards

Viewing 1 to 50 of 11555
A-10 Aircraft Oxygen Equipment Committee -
2014-10-30
ABSTRACT Solid chemical oxygen supplies of interest to aircraft operations are 'chlorate candles' and potassium superoxide (KO(sub)2). Chlorate candles are used in passenger oxygen supply units and ot...
SAE TECHNICAL STANDARDS
EG-1E Gas Turbine Test Facilities and Equipment -
2014-10-30
ABSTRACT This document discusses, in broad general terms, typical present instrumentation practice for post-overhaul gas turbine engine testing. Production engine testing and engine development work a...
SAE TECHNICAL STANDARDS
AE-5B Aircraft and Engine Fuel and Lubricant Sys Components -
2014-10-30
ABSTRACT This specification covers the general requirements for aircraft tank mounted, centrifugal type, fuel booster pumps, used for engine fuel feed and/or fuel transfer.
SAE TECHNICAL STANDARDS
AE-8C2 Terminating Devices and Tooling Committee -
2014-10-30
ABSTRACT Scope is unavailable.
SAE TECHNICAL STANDARDS
G-14 Americas Aerospace Quality Standards Committee (AAQSC) -
2014-10-30
ABSTRACT The aviation, space, and defense industries rely on the development and manufacture of complex products comprised of multiple systems, subsystems, and components each designed by individual d...
SAE TECHNICAL STANDARDS
A-6C2 Seals Committee -
2014-10-30
ABSTRACT This SAE Aerospace Recommended Practice (ARP) addresses the general requirements for data recording procedures, packaging, and storing of elastomeric seals and seal assemblies which include a...
SAE TECHNICAL STANDARDS
Seat Belt Systems Standards Committee -
2014-10-28
ABSTRACT This SAE Recommended Practice specifies design recommendations for the location of seat belt assembly anchorages which will promote proper transfer of occupant restraint forces on the stronge...
SAE TECHNICAL STANDARDS
Seat Belt Systems Standards Committee -
2014-10-28
ABSTRACT This SAE Recommended Practice specifies performance requirements and test procedures for the strength and location of seat belt assembly anchorages. It applies to seat belt anchorages attache...
SAE TECHNICAL STANDARDS
AMS G Titanium and Refractory Metals Committee -
2014-10-28
ABSTRACT This specification covers one grade of commercially-pure titanium in the form of sheet, strip, and plate.
SAE TECHNICAL STANDARDS
A-6C2 Seals Committee -
2014-10-27
ABSTRACT This specification and part standard covers polytetrafluoroethylene (PTFE) resin material and the dimensional requirements for scarf-cut retainers (back-up rings) previously covered by MIL-R-...
SAE TECHNICAL STANDARDS
E-25 General Standards for Aerospace and Propulsion Systems -
2014-10-27
ABSTRACT Scope is unavailable.
SAE TECHNICAL STANDARDS
AMS G Titanium and Refractory Metals Committee -
2014-10-27
ABSTRACT This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, and of flash welded rings and stock for flash welded rings.
SAE TECHNICAL STANDARDS
AMS G Titanium and Refractory Metals Committee -
2014-10-27
ABSTRACT This specification covers a titanium alloy in the form of sheet, strip, and plate up through 4.000 inches (101.60 mm), inclusive.
SAE TECHNICAL STANDARDS
Protective and Control Devices -
2014-10-27
ABSTRACT Scope is unavailable.
SAE TECHNICAL STANDARDS
Truck and Bus Foundation Brake Committee -
2014-10-27
ABSTRACT This SAE Recommended Practice provides the method to assign numerical values of brake effectiveness, using data from single station inertia dynamometer effectiveness tests, and to identify a ...
SAE TECHNICAL STANDARDS
Truck and Bus Foundation Brake Committee -
2014-10-27
ABSTRACT This SAE Recommended Practice provides the test procedure and methods to calculate the effectiveness of brake blocks, using an inertia dynamometer. To minimize testing variability, and to opt...
SAE TECHNICAL STANDARDS
Committee on Automotive Rubber Specs -
2014-10-27
ABSTRACT This SAE Standard provides a system for specifying significant material properties of thermoplastic elastomers (TPEs) that are intended for, but not limited to, use in automotive applications...
SAE TECHNICAL STANDARDS
Textile and Flexible Plastics Committee -
2014-10-27
ABSTRACT The practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified color standard. This practice is intended for use with...
SAE TECHNICAL STANDARDS
AE8-D Wire and Cable Committee -
2014-10-27
ABSTRACT AS22759 specification covers fluoropolymer-insulated single conductor electrical wires made with tin-coated, silver-coated, or nickel-coated conductors of copper or copper alloy as specified ...
SAE TECHNICAL STANDARDS
Motorcycle Technical Steering Committee -
2014-10-24
ABSTRACT This test procedure provides a standard method for evaluating the side stand retraction performance of a side stand/motorcycle combination. This test procedure applies to any two-wheeled moto...
SAE TECHNICAL STANDARDS
Motorcycle Technical Steering Committee -
2014-10-24
ABSTRACT These requirements define minimum recommended levels of side stand retraction performance of a new side stand/motorcycle combination when tested according to the procedures of SAE J1578. Thes...
SAE TECHNICAL STANDARDS
CTTC C1, Hydraulic Systems -
2014-10-24
ABSTRACT This SAE Recommended Practice has been set up by Subcommittee 4 of the Off-Road Machinery Technical Committee and is primarily for directional control valves on construction and industrial ma...
SAE TECHNICAL STANDARDS
MTC C5, Excavators -
2014-10-24
ABSTRACT This SAE Standard applies to all machines with shovel, clam, or dragline attachment. The purpose of this document is to provide a uniform method for determining the SAE rated capacity and SAE...
SAE TECHNICAL STANDARDS
Motorcycle Technical Steering Committee -
2014-10-24
ABSTRACT This SAE Recommended Practice is intended for use only in characterizing test surfaces used in motorcycle side stand retraction testing (SAE J1578). The equipment and procedure described in t...
SAE TECHNICAL STANDARDS
Battery Materials Testing Committee -
2014-10-24
ABSTRACT This SAE RP provides a set of test methods and practices for the characterization of the properties of Li-battery cathode active material. It is not within the scope of this document to estab...
SAE TECHNICAL STANDARDS
HFTC6, Operator Accommodation -
2014-10-24
ABSTRACT This SAE Standard establishes uniform test procedures for the defrosting systems of off-road, self-propelled work machines used in construction, general purpose industrial, agricultural, and ...
SAE TECHNICAL STANDARDS
MTC4, Forestry and Logging Equipment -
2014-10-21
ABSTRACT This SAE Standard provides a uniform method to calculate the lift capacity of knuckle-boom log loaders and certain forestry equipment. It establishes definitions and specifies machine conditi...
SAE TECHNICAL STANDARDS
Hybrid - EV Committee -
2014-10-21
ABSTRACT This SAE Technical Information Report SAE J2931/4 establishes the specifications for physical and data-link layer communications using broadband Power Line Communications (PLC) between the pl...
SAE TECHNICAL STANDARDS
Truck and Bus Hydraulic Brake Committee -
2014-10-21
ABSTRACT This Recommended Practice is derived from OEM and tier-1 laboratory tests and applies to two-axle multipurpose passenger vehicles, or trucks with a GVWR above 4536 kg (10 000 pounds) equipped...
SAE TECHNICAL STANDARDS
E-25 General Standards for Aerospace and Propulsion Systems -
2014-10-20
ABSTRACT Scope is unavaialble.
SAE TECHNICAL STANDARDS
AMS P Polymeric Materials Committee -
2014-10-20
ABSTRACT This specification covers one width and one strength of low modulus aramid tubular webbing. This product has been used typically in construction of parachutes. 9/16 inch (14 mm) wide low modu...
SAE TECHNICAL STANDARDS
E-25 General Standards for Aerospace and Propulsion Systems -
2014-10-20
ABSTRACT Scope is unavailable.
SAE TECHNICAL STANDARDS
AE-8C2 Terminating Devices and Tooling Committee -
2014-10-20
ABSTRACT Scope is unavailable.
SAE TECHNICAL STANDARDS
AE-8C1 Connectors Committee -
2014-10-16
ABSTRACT This specification covers four series of electrical connectors (plugs and receptacles) with removable crimp contacts and accessories (see 6.1). AS81511 connectors are not recommended for new ...
SAE TECHNICAL STANDARDS
A-10 Aircraft Oxygen Equipment Committee -
2014-10-16
ABSTRACT The scope of this document is to provide a list of documents of types pertaining to the effects of oxygen on ignition and combustion of materials. Consolidating these references in one place ...
SAE TECHNICAL STANDARDS
A-10 Aircraft Oxygen Equipment Committee -
2014-10-16
ABSTRACT The purpose of this standard is to establish optimum standards for crew demand and pressure-breathing oxygen mask assemblies for use by crew members in civil aircraft. This standard covers bo...
SAE TECHNICAL STANDARDS
Fuel Cell Standards Committee -
2014-10-16
ABSTRACT This SAE Recommended Practice establishes uniform procedures for testing fuel cell and hybrid fuel cell electric vehicles, excluding low speed vehicles, designed primarily for operation on th...
SAE TECHNICAL STANDARDS
AE-8C1 Connectors Committee -
2014-10-16
ABSTRACT Scope is unavailable.
SAE TECHNICAL STANDARDS
AE-8C1 Connectors Committee -
2014-10-16
ABSTRACT Scope is unavailable.
SAE TECHNICAL STANDARDS
AE-8C1 Connectors Committee -
2014-10-16
ABSTRACT Scope is unavailable.
SAE TECHNICAL STANDARDS
AE-8C1 Connectors Committee -
2014-10-16
ABSTRACT Scope is unavailable.
SAE TECHNICAL STANDARDS
Viewing 1 to 50 of 11555