Criteria

Text:
Content:
Display:

Results

Viewing 271 to 300 of 1847
CURRENT
2015-02-26
Standard
J1623_201502
This SAE Recommended Practice provides test procedures and performance requirements for off-highway vehicle headlamps.
CURRENT
2015-02-26
Standard
J2593_201502
This information report provides general information for installing and tightening fluid conductors and connectors. Following these guidelines, with the consistent proper use of torque wrenches, tightening procedures and correct torque levels will result in diminishing leaks and improving service life by avoiding hose twisting, tube binding, false torque and improper joint closures. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, this report should not be used as a “standard” nor a “specification” and the values shown should not be construed as “guaranteed” minimums, maximums or absolutes. This document is an information report to help users by gathering available information from the various connector standards and publishing the information in one source for easy retrieval and applied common usage. This information report is primarily intended for mobile/stationary industrial equipment applications.
CURRENT
2015-02-20
Standard
J1671_201502
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
HISTORICAL
2015-02-18
Standard
J1939/84_201502
The purpose of this Recommended Practice is to verify that vehicles and/or components are capable of communicating a required set of information, in accordance with the diagnostic messages specified in SAE J1939-73, to fulfill the off-board diagnostic tool interface requirements contained in the government regulations cited below. This document describes the tests, methods, and results for verifying diagnostic communications from an off board diagnostic tool (i.e., scan tool) to a vehicle and/or component. SAE members have generated this document to serve as a guide for testing vehicles for compliance with ARB and other requirements for emissions-related on-board diagnostic (OBD) functions for heavy duty engines used in medium and heavy duty vehicles. The development of HD OBD regulations by US EPA and California’s Air Resources Board (ARB) require that diagnostic message services are exercised to evaluate diagnostic communication standardization requirements on production vehicles.
CURRENT
2015-02-03
Standard
J44_201502
This SAE Recommended Practice establishes performance requirements for hand-operated brake systems on recreational, noncompetition snowmobiles.
CURRENT
2015-01-23
Standard
J551/1_201501
This SAE Standard covers the measurement of radio frequency radiated emissions and immunity. Each part details the requirements for a specific type of electromagnetic compatibility (EMC) test and the applicable frequency range of the test method. The methods are applicable to a vehicle, boat, machine or device powered by an internal combustion engine or battery powered electric motor. Operation of all engines or motors (main and auxiliary) of a vehicle, boat, machine or device is included. All equipment normally operating when the vehicle, boat, machine or device is in operation is included. Operator controlled equipment is included or excluded as specified in the individual document parts. As a special case, CISPR 12 applies to battery powered floor finishing equipment, but robot carpet sweepers are excluded. By reference, IEC CISPR 12 and CISPR 25 are adopted as the standards for the measurement of vehicle emissions.
CURRENT
2015-01-20
Standard
J1212_201501
This document applies to off-road forestry work machines defined in SAE J1116 or ISO 6814.
CURRENT
2015-01-08
Standard
J1791_201501
This SAE standard applies to self-propelled driver operated sweepers and scrubbers as defined in SAE J2130-1.
HISTORICAL
2015-01-08
Standard
J185_201501
Minimum criteria are provided for steps, stairways, ladders, walkways, platforms, handrails, handholds, guardrails, and entrance openings which permit ingress to and egress from operator, inspection, maintenance or service platforms on off-road work machines parked in accordance with the manufacturer's instructions.
CURRENT
2014-12-03
Standard
J1521_201412
This SAE Recommended Practice describes two-dimensional, 95th percentile truck driver, side view, seated shin-knee contours for both the accelerator operating leg and the clutch operating leg for horizontally adjustable seats (see Figure 1). There is one contour for the clutch shin-knee and one contour for the accelerator shin-knee. There are three locating equations for each curve to accommodate male-to-female ratios of 50:50, 75:25, and 90:10 to 95:5.
CURRENT
2014-12-03
Standard
J1948_201412
This SAE Recommended Practice provides a standardized test procedure for heavy-duty truck sleeper berth restraints to determine whether they meet the FMCSR 393.76(h) requirements.
CURRENT
2014-12-03
Standard
J2685_201412
This SAE Recommended Practice defines the test conditions, procedures, and performance requirements for PTC (positive temperature coefficient of resistance) overcurrent protection devices. PTCs are typically either polymeric (PPTC) or ceramic (CPTC). It is important to note battery voltages versus powernets/system voltage versus max battery voltages: (12 V/14 V/16 V, 24 V/28 V/32 V, and 36 V/42 V/58 V). All voltages are DC. These devices are typically rated with a maximum operating voltage, which for vehicular systems need to be 16 V (for 12 V batteries), 32 V (for 24 V batteries), and 58 V (for 36 V batteries/42 V powernets). PTC devices are considered to be self-resetting after responding to overcurrent conditions and after such condition has been removed from the affected circuit containing the PTC.
CURRENT
2014-12-03
Standard
J1522_201412
This SAE Recommended Practice describes two-dimensional 95th percentile truck driver side view, seated stomach contours for horizontally adjustable seats (see Figure 1). There is one contour and three locating lines to accommodate male-to-female ratios of 50:50, 75:25, and 90:10 to 95:5.
CURRENT
2014-12-02
Standard
J2139_201412
This SAE Recommended Practice provides standardized laboratory tests, test methods, and performance requirements applicable to signal and marking devices used on vehicles 2032 mm or more in overall width.
CURRENT
2014-11-25
Standard
J267_201411
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of wheels and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose vehicles. Users may establish design criteria exceeding the minimum performance requirement for added confidence in a design. The cycle requirements noted in Tables 1 and 2 are based on Weibull statistics using 2 parameter, median ranks, 50% confidence level and 90% reliability, and beta equal to 2, typically noted as B10C50. For other wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. For bolt together military wheels, see SAE J1992. This document does not cover other special application wheels and rims.
CURRENT
2014-11-24
Standard
J2698_201411
This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase nominal 120 VAC circuits that provide power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off. The power supply comes from alternative sources such as land-based grid power, DC-AC inverters and auxiliary power generators. The circuits may also provide power to improve vehicle performance through charging batteries or operating cold-weather starting aids.
CURRENT
2014-11-20
Standard
J2378_201411
This SAE Recommended Practice provides instructions and test procedures for air braked trailers and dollies used in single and multiple trailer combinations on highway. This document is not intended for off-highway application.
CURRENT
2014-11-20
Standard
ARP1308D
The intent of this ARP is to identify electrical connectors maintained by the AE-8C1 Committee, to provide their general application characteristics, associated configuration options, and recommendations for new design (see 6.1.1), repair, and retrofit purposes (see 6.1). It is acknowledged the connectors listed herein will not completely satisfy all mobility vehicle and equipment requirements, but optimization of the use of these components will facilitate standardization in the form of maximum utilization of a minimum variety of connectors. This ARP only pertains to AS connector standards. See MIL-STD-1353 for U.S. military specification connector information.
2014-11-19
WIP Standard
J1451
This dictionary of terms was prepared for use by those with a need to describe and understand the dynamics and handling of two-wheeled, single track vehicles. It is intended to span the gap between vehicle dynamics specialists and those with a more general interest. This report is pertinent to such areas as vehicle design and development, the description of two-wheeler properties, rider training and education, and the preparation of standards and regulations. This report was prepared by the SAE Motorcycle Committee, which solicits suggestions for improvements and additions to be considered in future revisions. Comments should be directed to SAE Headquarters.
CURRENT
2014-11-18
Standard
J1214_201411
The purpose of this SAE Recommended Practice is set guidelines for tire to wheel house and body clearances on recreational vehicles.
CURRENT
2014-11-15
Standard
J1476_201411
This SAE Recommended Practice establishes a method of evaluating the structural integrity of the parking brake system of all new trucks, buses, and combination vehicles designed for roadway use in the following classifications: TRACTOR, TRAILER, TRUCK, AND BUS: over 4500 kg (10 000 lb) GVWR.
CURRENT
2014-11-15
Standard
J1404_201411
This SAE Recommended Practice presents requirements for the structural integrity of the brake system of all new trucks, buses, and combinations of vehicles designed for roadway use and falling into the following classifications: Truck and Bus—Over 4500 kg (10 000 lb) GVWR Combination Vehicles—Towing vehicle over 4500 kg (10 000 lb) GVWR The requirements are based on data obtained from SAE J294.
CURRENT
2014-11-15
Standard
J1713_201411
This SAE Recommended Practices specifies a procedure for determining structural strength and fatigue life of disc-brake caliper assemblies which are satisfactory for vehicle usage. It is applicable to new caliper assemblies which are employed in passenger car and truck brake systems utilizing hydraulic brake fluids. Brake design and vehicle performance requirements are not included. Specification limits are left to the discretion of the responsible manufacturer. This procedure was developed for base brake operation and does not consider some unusual effects of ABS (Anti-Lock-Brake System) or Traction Control systems which may have a significant effect on the caliper. Careful analysis of the particular type ABS and/or Traction Control should be made and additional tests may be required which are not included in this document.
CURRENT
2014-11-14
Standard
TSB001_201411
HISTORICAL
2014-11-04
Standard
J2403DA_201411
This document is intended to supplement SAE J2403 by providing the content of Table 1, Table 2, and Table 3 from SAE J2403 in a form that can be sorted and searched for easier use. It is NOT intended as a substitute for the actual document, and any discrepancies between this Digital Annex and the published SAE J2403 document must be resolved in favor of the published document. This document provides the content of Table 1 and Table 2 published in SAE J2403 into the single table in the 'Term' tab, while the 'Recommended Term Definitions' tab provides the content of Table 3 in SAE J2403 and the 'Glossary' tab provides the content of Table 4 in SAE J2403.
2014-10-27
WIP Standard
J1783
This SAE Recommended Practice provides the designer with guidance for the selection of directional control valves for use in the hydraulic systems of surface ships and submersibles. This guidance includes use of standard valves and interfaces, minimum envelopes that should be reserved to permit interchangeability, environmental considerations, and general technical requirements.
CURRENT
2014-10-27
Standard
J1802_201410
This SAE Recommended Practice provides the test procedure and methods to calculate the effectiveness of brake blocks, using an inertia dynamometer. To minimize testing variability, and to optimize standardization and correlation, a single, high volume size of brake block is specified (FMSI No. 4515E) and evaluated in a reference S-cam brake assembly of 419 mm x 178 mm (16.5 in x 7.0 in) size, using a specified brake drum.
CURRENT
2014-10-27
Standard
J1801_201410
This SAE Recommended Practice provides the method to assign numerical values of brake effectiveness, using data from single station inertia dynamometer effectiveness tests, and to identify a uniform procedure to mark these values on the edge of brake blocks in excess of 12.7 mm (0.51 in) in thickness.
CURRENT
2014-10-24
Standard
J1535_201410
This SAE Standard establishes uniform test procedures for the defrosting systems of off-road, self-propelled work machines used in construction, general purpose industrial, agricultural, and forestry machinery as referenced in table one of this document. It includes tests that can be conducted with uniform test equipment in commercially available laboratory facilities, as well as in an appropriate outdoor environment.
CURRENT
2014-10-24
Standard
J748_201410
This SAE Recommended Practice has been set up by Subcommittee 4 of the Off-Road Machinery Technical Committee and is primarily for directional control valves on construction and industrial machinery equipment as referenced in SAE J1116. The purpose is to establish port area to flow relationship and match valve spool eye ends in relation to rated capacity. Port connections are optional for either the 4-bolt split flange connection or the internal straight thread "O" ring connection.
Viewing 271 to 300 of 1847