Criteria

Text:
Content:
Display:

Results

Viewing 151 to 180 of 1861
CURRENT
2015-10-08
Standard
J1810_201510
This SAE Standard describes those factors which affect the accuracy and reliability of voltage indicating units and electrical indicating and sending units for fuel level, pressure, and temperature suitable for off-road, self-propelled work machines as described in SAE J1116 and agricultural tractors as defined in ASAE S390. Indicating units are divided into two groups, fully sealed and partially sealed. Serviceable lighting is not covered by this document unless otherwise specified. No ISO document has been found to be compatible.
HISTORICAL
2002-10-31
Standard
J1811_200210
This SAE Standard is intended for light and heavy-duty on-highway trucks and their trailers; and off-road machinery applications as described in SAE J1116. The terminals described in this document are primarily used to connect batteries, cranking motors, solenoids, magnetic switches, and master disconnect switches and power cable assemblies.
CURRENT
2016-06-17
Standard
J1861_201606
This SAE Recommended Practice establishes minimum tolerance requirements for pilot operated and mechanically actuated modulating type valves, and through type valves used in the service brake control system when tested in accordance with the test procedure outlined in SAE J1859. This document applies to the nominal input-output characteristics as specified by vehicle original equipment manufacturer and labeled by the valve manufacturer as outlined in SAE J1860. The tolerance requirements will include: Crack (opening) pressure or force. Crack pressure may be measured at the initial output pressure or as the pressure differential before output pressure exceeds 14 kPa (2 psi). Crack force may be measured at initial output pressure or before output pressure exceeds 14 kPa (2 psi). Pressure differential (input-output)
HISTORICAL
2011-09-12
Standard
J1861_201109
This SAE Recommended Practice establishes minimum tolerance requirements for pilot operated and mechanically actuated modulating type valves, and through type valves used in the service brake control system when tested in accordance with the test procedure outlined in SAE J1859. This document applies to the nominal input-output characteristics as specified by vehicle original equipment manufacturer and labeled by the valve manufacturer as outlined in SAE J1860. The tolerance requirements will include: Crack (opening) pressure or force. Crack pressure may be measured at the initial output pressure or as the pressure differential before output pressure exceeds 14 kPa (2 psi). Crack force may be measured at initial output pressure or before output pressure exceeds 14 kPa (2 psi). Pressure differential (input-output)
HISTORICAL
2007-01-19
Standard
J1861_200701
This SAE Recommended Practice establishes minimum tolerance requirements for pilot operated and mechanically actuated modulating type valves, and through type valves used in the service brake control system when tested in accordance with the test procedure outlined in SAE J1859. This document applies to the nominal input-output characteristics as specified by vehicle original equipment manufacturer and labeled by the valve manufacturer as outlined in SAE J1860. The tolerance requirements will include: A. Crack (opening) pressure or force b. Pressure differential (input-output)
CURRENT
2016-06-14
Standard
J1860_201606
This SAE Recommended Practice applies to those air brake system valves used to control the vehicle service brakes and test procedures defined by SAE J1859 to measure performance characteristics. This Recommended Practice adheres to standard industry practice of using English units for specifying valve characteristics.
HISTORICAL
2003-04-25
Standard
J1860_200304
This SAE Recommended Practice applies to those air brake system valves used to control the vehicle service brakes and test procedures defined by SAE J1859 to measure performance characteristics. This Recommended Practice adheres to standard industry practice of using English units for specifying valve characteristics. Purpose The purpose of this document is to provide a means of identifying vehicle air brake system components with performance (input-output) characteristics. This labeling procedure intends to identify and facilitate proper in-service valve replacement. Nomenclature and test procedure are defined in either SAE J656 or SAE J1859 respectively.
CURRENT
2016-07-01
Standard
J1865_201607
This SAE Recommended Practice defines a clearance line for establishing dimensional compatibility between drum brakes and wheels with 19.5 inch, 22.5 inch, and 24.5 inch diameter rims. Wheels designed for use with drum brakes may not be suitable for disc brake applications. The lines provided establish the maximum envelope for brakes, including all clearances, and minimum envelope for complete wheels to allow for interchangeability. This document addresses the dimensional characteristics only, and makes no reference to the performance, operational dynamic deflections, or heat dissipation of the system. Valve clearances have not been included in the fitment lines. Bent valves may be required to clear brake drums. Disc brake applications may require additional running clearances beyond those provided by the minimum contour lines. Mounting systems as noted are referenced in SAE J694.
HISTORICAL
1999-06-01
Standard
J1865_199906
This SAE Recommended Practice defines a clearance line for establishing dimensional compatibility between drum brakes and wheels with 19.5 in, 22.5 in, and 24.5 in diameter rims. The clearance line establishes the maximum envelope for brakes and minimum envelope for complete wheels to allow for interchangeability. This document addresses the dimensional characteristics only, and makes no reference to the performance, operational dynamic deflections, or heat dissipation of the system. Valve clearances have not been included in the fitment lines. Bent valves may be required to clear brake drums. Mounting systems as noted are referenced in SAE J694.
HISTORICAL
2007-07-31
Standard
J1865_200707
This SAE Recommended Practice defines a clearance line for establishing dimensional compatibility between drum brakes and wheels with 19.5 in, 22.5 in, and 24.5 in diameter rims. Wheels designed for use with drum brakes may not be suitable for disc brake applications. The clearance line establishes the maximum envelope for brakes and minimum envelope for complete wheels to allow for interchangeability. This document addresses the dimensional characteristics only, and makes no reference to the performance, operational dynamic deflections, or heat dissipation of the system. Valve clearances have not been included in the fitment lines. Bent valves may be required to clear brake drums. Disc brake applications may require additional running clearances beyond those provided by the minimum contour lines. Mounting systems as noted are referenced in SAE J694.
CURRENT
2014-05-07
Standard
J1702_201405
This SAE Standard establishes a method of disclosing the sweep-ability performance of self-propelled sweepers that use broom means for sweeping and collection, together with either a mechanical- or pneumatic-conveyance system for the transfer of “sweepings” into a collection hopper.
HISTORICAL
2007-11-05
Standard
J1702_200711
This SAE Standard establishes a method of disclosing the sweep-ability performance of self-propelled sweepers that use broom means for sweeping and collection, together with either a mechanical- or pneumatic-conveyance system for the transfer of "sweepings" into a collection hopper. The purpose of this document sets out to describe a test practice for gauging the sweep-ability performance by sweepers described in SAE J2130 together with a format for the presentation of the test results. The document can be used to disclose or compare particular operating performance criteria for similar conditions.
CURRENT
1985-03-01
Standard
J169_198503
The purpose of this document is to establish air conditioning design guidelines that will apply to most systems rather than the specific design of any particular system. Operating conditions and characteristics of the equipment will determine the design of any successful system, and since these characteristics and conditions vary greatly from one application to another, the designer must determine the goals expected to be reached under the conditions encountered. To determine the capacity of such items as blowers, condenser fans, condenser coils, evaporator coils, filters, compressors, etc., will require the adherence to several guidelines, some of which are outlined in the following paragraphs.
HISTORICAL
2004-08-25
Standard
J1708_200408
This SAE Recommended Practice document defines a recommended practice for implementing a bidirectional, serial communication link among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and basic software compatibility such as interface requirements, system protocol, and message format. The actual data to be transmitted by particular modules, which is an important aspect of communications compatibility, is not specified in this document. These and other details of communications link implementation and use should be specified in the separate application documents referenced in Section 2. Save money while getting up-to-date access to the standards you need! Subscribe to the SAE J1939 Standards Collection on the Web and get one year of anytime access and automatic updates to the J1939 family of documents, plus all cross-referenced and selected related documents.
CURRENT
2016-09-13
Standard
J1708_201609
This SAE Recommended Practice defines a recommended practice for implementing a bidirectional, serial communication link among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and basic software compatibility such as interface requirements, system protocol, and message format. The actual data to be transmitted by particular modules, which is an important aspect of communications compatibility, is not specified in this document. These and other details of communication link implementation and use should be specified in the separate application documents referenced in Section 2.
CURRENT
2014-11-15
Standard
J1713_201411
This SAE Recommended Practices specifies a procedure for determining structural strength and fatigue life of disc-brake caliper assemblies which are satisfactory for vehicle usage. It is applicable to new caliper assemblies which are employed in passenger car and truck brake systems utilizing hydraulic brake fluids. Brake design and vehicle performance requirements are not included. Specification limits are left to the discretion of the responsible manufacturer. This procedure was developed for base brake operation and does not consider some unusual effects of ABS (Anti-Lock-Brake System) or Traction Control systems which may have a significant effect on the caliper. Careful analysis of the particular type ABS and/or Traction Control should be made and additional tests may be required which are not included in this document.
CURRENT
2017-08-14
Standard
J1731_201708
This SAE Recommended Practice describes STANDARD-DUTY and EXTREME-DUTY Pilot Bearing requirements and sizes for class 6, 7, and 8 on-highway trucks and buses that use diesel engines and manual transmissions. The recommendations may apply to a wide range of other pilot-bearing applications, such as agricultural, industrial, and construction equipment.
HISTORICAL
2001-06-12
Standard
J1731_200106
This SAE Recommended Practice describes STANDARD-DUTY and EXTREME-DUTY Pilot Bearing requirements and sizes for class 6, 7, and 8 on-highway trucks and buses that use diesel engines and manual transmissions. The recommendations may apply to a wide range of other pilot-bearing applications, such as agricultural, industrial, and construction equipment.
CURRENT
1999-06-01
Standard
J1741_199906
This SAE Standard describes methods for evaluating the performance of the systems detection device, the minimum detection areas behind the machine, the visual and audible information presented to the operator and ground personnel, and the systems fault detection requirements. Also included are operator system function tests and maintenance procedures.
CURRENT
2007-10-11
Standard
J1032_200710
The purpose of this SAE Recommended Practice is to provide a set of recognized definitions as a universally understood means of communication among all people interested in the inherent availability of off-Road Work machines. It is not the intent of this document to provide an absolute measure of unit availability. The intent is to provide common definitions for classifying and evaluating operation, repair, and maintenance data. This recommended practice applies to construction and general purpose industrial machines as categorized in SAE J1116. It describes the parameters related to the inherent availability of the covered classes of Off-Road Self-Propelled Work Machines.
HISTORICAL
2007-01-30
Standard
J1029_200701
This SAE Standard establishes minimum requirements for lighting and marking earthmoving construction machinery as defined in SAE J1116, 1.1 Self-Propelled Construction Machines - Earthmoving (excluding excavators). (Construction machinery is normally operated off-highway, and therefore this SAE document is not intended to be used as a basis for regulations by those having authority over on-highway motor vehicles.)
CURRENT
2012-10-09
Standard
J1029_201210
This SAE Standard establishes minimum requirements for lighting and marking earthmoving construction machinery as defined in SAE J1116, 1.1 Self-Propelled Construction Machines—Earthmoving (excluding excavators). (Construction machinery is normally operated off-highway, and therefore this SAE document is not intended to be used as a basis for regulations by those having authority over on-highway motor vehicles.)
HISTORICAL
1980-10-01
Standard
J1028_198010
This SAE Recommended Practice applies to stationary usage of mobile construction-type cranes, crawler or rubber-tire mounted, on outriggers or on tires, when used for lifting crane, clamshell, dragline, magnet, pile driver, or similar service.
HISTORICAL
1980-08-01
Standard
J1028_198008
This SAE Recommended Practice applies to stationary usage of mobile construction-type cranes, crawler or rubber-tire mounted, on outriggers or on tires, when used for lifting crane, clamshell, dragline, magnet, pile driver, or similar service.
HISTORICAL
1996-09-01
Standard
J1029_199609
This SAE Standard establishes minimum requirements for lighting and marking earthmoving construction machinery as defined in SAE J1116, 1.1 Self-Propelled Construction Machines—Earthmoving (excluding excavators). (Construction machinery is normally operated off-highway, and therefore this SAE document is not intended to be used as a basis for regulations by those having authority over on-highway motor vehicles.)
CURRENT
1998-10-01
Standard
J1028_199810
This SAE Recommended Practice applies to stationary usage of mobile construction-type cranes, crawler or rubber-tire mounted, on outriggers or on tires, when used for lifting crane, clamshell, dragline, magnet, pile driver, or similar service.
CURRENT
2000-02-07
Standard
J1026_200002
This SAE Standard applies to crawler tractors and crawler loaders as identified in SAE J1057 and SAE J1116 and having a manufacturer's maximum specified speed of 16 km/h.
2017-08-16
WIP Standard
J1028
This SAE Recommended Practice applies to stationary usage of mobile construction-type cranes, crawler or rubber-tire mounted, on outriggers or on tires, when used for lifting crane, clamshell, dragline, magnet, pile driver, or similar service.
HISTORICAL
1986-03-01
Standard
J1029_198603
This SAE Standard establishes minimum requirements for lighting and marking earthmoving construction machinery as defined in SAE J1116, 1.1 Self-Propelled Construction Machines - Earthmoving (excluding excavators). (Construction machinery is normally operated off-highway, and therefore this SAE document is not intended to be used as a basis for regulations by those having authority over on-highway motor vehicles.)
HISTORICAL
1977-10-01
Standard
J1026A_197710
This SAE Standard applies to crawler tractors and crawler loaders as identified in SAE J1057 and SAE J1116 and having a manufacturer's maximum specified speed of 16 km/h.
Viewing 151 to 180 of 1861