SAE Technical Standards

Viewing 1 to 50 of 11562
Hydraulic Brake Components Standards Committee -
2014-11-26
ABSTRACT This SAE Standard covers performance requirements and methods of test for master cylinder reservoir diaphragm gaskets that will provide a functional seal and protection from outside dirt and ...
SAE TECHNICAL STANDARDS
AMS F Corrosion Heat Resistant Alloys Committee -
2014-11-25
ABSTRACT This SAE Aerospace Recommended Practice (ARP) describes procedures for the determination of trace elements listed in AMS2280 for Nickel, Cobalt, and Iron-based high temperature alloys.
SAE TECHNICAL STANDARDS
AE-5A Aerospace Fuel, Inerting and Lubrication Sys Committee -
2014-11-25
ABSTRACT To describe general guidelines for achieving selected levels of cleanliness in gas turbine engine fuel system components and to describe laboratory methods for measuring and reporting the con...
SAE TECHNICAL STANDARDS
AMS E Carbon and Low Alloy Steels Committee -
2014-11-25
ABSTRACT Primarily to provide the aerospace industry with approximate standards for comparing various shaped sections to round bars, in determining the response to hardening characteristics when heat ...
SAE TECHNICAL STANDARDS
S-9 Cabin Safety Provisions Committee -
2014-11-25
ABSTRACT This specification covers the following types and classes of extinguishers: Type I Stored pressure type: Category A - Operational Temperature range -40 to +140 °F (-40 to +60 °C), Category B ...
SAE TECHNICAL STANDARDS
E-25 General Standards for Aerospace and Propulsion Systems -
2014-11-25
ABSTRACT Scope is unavailable.
SAE TECHNICAL STANDARDS
E-25 General Standards for Aerospace and Propulsion Systems -
2014-11-25
ABSTRACT Scope is unavailable.
SAE TECHNICAL STANDARDS
E-25 General Standards for Aerospace and Propulsion Systems -
2014-11-25
ABSTRACT Scope is unavailable.
SAE TECHNICAL STANDARDS
Truck and Bus Wheel Committee -
2014-11-25
ABSTRACT This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of wheels and demountable rims intended for normal highway use on...
SAE TECHNICAL STANDARDS
Truck and Bus Electrical Systems Committee -
2014-11-24
ABSTRACT 1.1 This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase ...
SAE TECHNICAL STANDARDS
A-6C2 Seals Committee -
2014-11-20
ABSTRACT This SAE Aerospace Standard (AS) covers scarf-cut polytetrafluoroethylene (PTFE) retainers (back-up rings) for use in static glands in accordance with AS5857. They are for use in hydraulic an...
SAE TECHNICAL STANDARDS
AE-8C1 Connectors Committee -
2014-11-20
ABSTRACT The intent of this ARP is to identify electrical connectors maintained by the AE-8C1 Committee, to provide their general application characteristics, associated configuration options, and rec...
SAE TECHNICAL STANDARDS
AE-5B Aircraft and Engine Fuel and Lubricant Sys Components -
2014-11-20
ABSTRACT This SAE Aerospace Recommended Practice (ARP) delineates two complementary filter element performance ratings: (1) dirt capacity, and (2) filtration efficiency, and corresponding test procedu...
SAE TECHNICAL STANDARDS
A-5C Aircraft Tires Committee -
2014-11-20
ABSTRACT This SAE Aerospace Standard (AS) sets forth criteria for the selection and verification processes to be followed in providing tires that will be suitable for intended use on civil aircraft. T...
SAE TECHNICAL STANDARDS
AE-8C1 Connectors Committee -
2014-11-20
ABSTRACT Scope is unavailable.
SAE TECHNICAL STANDARDS
A-6B1 Hydraulic Servo Actuation Committee -
2014-11-20
ABSTRACT This ARP is intended to promote better understanding of gas system characteristics and operation in order to aid in system selection and design. Various gas systems are classified in a broad ...
SAE TECHNICAL STANDARDS
Truck and Bus Brake Systems Committee -
2014-11-20
ABSTRACT This SAE Recommended Practice provides instructions and test procedures for air braked trailers and dollies used in single and multiple trailer combinations on highway. This document is not i...
SAE TECHNICAL STANDARDS
A-6C2 Seals Committee -
2014-11-20
ABSTRACT Scope is unavailable.
SAE TECHNICAL STANDARDS
G-33 Configuration Management -
2014-11-20
ABSTRACT This document applies to hardware and software and provides CM requirements to be placed on contracts after being tailored by the Acquirer. The requirements have been organized by the followi...
SAE TECHNICAL STANDARDS
Human Accom and Design Devices Stds Comm -
2014-11-19
ABSTRACT This recommended practice is a source of information for body and trim engineers and represents existing technology in the field of on-highway vehicle seating systems. It provides a more unif...
SAE TECHNICAL STANDARDS
Trailer Committee -
2014-11-18
ABSTRACT The purpose of this SAE Recommended Practice is set guidelines for tire to wheel house and body clearances on recreational vehicles.
SAE TECHNICAL STANDARDS
AMS D Nonferrous Alloys Committee -
2014-11-18
ABSTRACT This specification has been declared “NONCURRENT” by the Aerospace Materials Division, SAE, as of August 2009. It is recommended, therefore, that this specification not be specified for new d...
SAE TECHNICAL STANDARDS
Hydraulic Brake Components Standards Committee -
2014-11-15
ABSTRACT This SAE Recommended Practices specifies a procedure for determining structural strength and fatigue life of disc-brake caliper assemblies which are satisfactory for vehicle usage. It is appl...
SAE TECHNICAL STANDARDS
Truck and Bus Foundation Brake Committee -
2014-11-15
ABSTRACT This SAE Recommended Practice presents requirements for the structural integrity of the brake system of all new trucks, buses, and combinations of vehicles designed for roadway use and fallin...
SAE TECHNICAL STANDARDS
Truck and Bus Foundation Brake Committee -
2014-11-15
ABSTRACT This SAE Recommended Practice establishes a method of evaluating the structural integrity of the parking brake system of all new trucks, buses, and combination vehicles designed for roadway u...
SAE TECHNICAL STANDARDS
AMS D Nonferrous Alloys Committee -
2014-11-14
ABSTRACT This specification has been declared “NONCURRENT” by the Aerospace Materials Division, SAE, as of August 2009. It is recommended, therefore, that this specification not be specified for new d...
SAE TECHNICAL STANDARDS
AMS F Corrosion Heat Resistant Alloys Committee -
2014-11-14
ABSTRACT This specification covers an extra high toughness, corrosion-resistant steel in the form of bars, wire, forgings, flash welded rings, extrusions, and stock for forging, flash welded rings, or...
SAE TECHNICAL STANDARDS
ACBG Rolling Element Bearing Committee -
2014-11-13
ABSTRACT No abstract available.
SAE TECHNICAL STANDARDS
ACBG Rolling Element Bearing Committee -
2014-11-13
ABSTRACT No abstract available.
SAE TECHNICAL STANDARDS
G-23 Manufacturing Management Committee -
2014-11-13
ABSTRACT This standard is applicable to all phases of the system acquisition life cycle. It is intended for use on all programs with manufacturing content. It requires proven manufacturing management ...
SAE TECHNICAL STANDARDS
AMS B Finishes Processes and Fluids Committee -
2014-11-13
ABSTRACT This specification establishes the requirements for dyed anodic coatings on aluminum alloys.
SAE TECHNICAL STANDARDS
A-10 Aircraft Oxygen Equipment Committee -
2014-11-13
ABSTRACT This document provides guidance concerning the maintenance and serviceability of oxygen cylinders beginning with the quality of oxygen that is required, supplemental oxygen information, handl...
SAE TECHNICAL STANDARDS
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies -
2014-11-13
ABSTRACT Scope unavailable.
SAE TECHNICAL STANDARDS
AE-8C2 Terminating Devices and Tooling Committee -
2014-11-11
ABSTRACT Scope unavailable.
SAE TECHNICAL STANDARDS
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies -
2014-11-11
ABSTRACT SCOPE IS UNAVAILABLE
SAE TECHNICAL STANDARDS
A-5A Wheels, Brakes and Skid Controls Committee -
2014-11-11
ABSTRACT This document outlines the development process and makes recommendations for total antiskid/aircraft systems compatibility. These recommendations encompass all aircraft systems that may affec...
SAE TECHNICAL STANDARDS
AE-8C2 Terminating Devices and Tooling Committee -
2014-11-11
ABSTRACT SCOPE IS UNAVAILABLE
SAE TECHNICAL STANDARDS
AE-8C2 Terminating Devices and Tooling Committee -
2014-11-11
ABSTRACT SCOPE IS UNAVAILABLE
SAE TECHNICAL STANDARDS
AE-8C2 Terminating Devices and Tooling Committee -
2014-11-11
ABSTRACT Scope is unavailable
SAE TECHNICAL STANDARDS
Truck and Bus Brake Systems Committee -
2014-11-11
ABSTRACT This SAE Recommended Practice (RP) provides test procedures for air braked trucks and truck-tractors used to tow single and multiple trailer combinations on highways. This RP is not intended ...
SAE TECHNICAL STANDARDS
AMS D Nonferrous Alloys Committee -
2014-11-07
ABSTRACT This specification covers aluminum alloy die castings.
SAE TECHNICAL STANDARDS
AMS CE Elastomers Committee -
2014-11-07
ABSTRACT This specification covers a silicone rubber in the form of sheet, strip, tubing, extrusions, and molded shapes. Primarily for parts required to operate or seal from -65 to +205 degrees C (-85...
SAE TECHNICAL STANDARDS
AMS D Nonferrous Alloys Committee -
2014-11-07
ABSTRACT This specification covers an aluminum alloy in the form of sheet and plate.
SAE TECHNICAL STANDARDS
A-6C2 Seals Committee -
2014-11-06
ABSTRACT This document contains data relative to the chemical nature of aerospace fluids and relates each to its empirical effect upon elastomeric components. Since the compatibilities of elastomers a...
SAE TECHNICAL STANDARDS
E-25 General Standards for Aerospace and Propulsion Systems -
2014-11-06
ABSTRACT SCOPE IS UNAVAILABLE.
SAE TECHNICAL STANDARDS
E-25 General Standards for Aerospace and Propulsion Systems -
2014-11-06
ABSTRACT SCOPE IS UNAVAILABLE.
SAE TECHNICAL STANDARDS
E-25 General Standards for Aerospace and Propulsion Systems -
2014-11-06
ABSTRACT SCOPE IS UNAVAILABLE.
SAE TECHNICAL STANDARDS
Viewing 1 to 50 of 11562