Criteria

Text:
Display:

Results

Viewing 1 to 30 of 8657
CURRENT
2017-11-20
Standard
J587_201711
This SAE Standard provides test procedures, requirements, and guidelines for vehicular license plate illumination devices.
CURRENT
2017-11-16
Standard
J3003_201711
This SAE Recommended Practice provides dimensional specifications for the 41/2 and 53/4 inch general service sealed lighting units, intended for use in such applications as motorcycle headlamps, military headlamps, industrial machinery headlamps, fog lamps, spot lamps, etc. See Figures 1 and 2 and Tables 1 and 2.
CURRENT
2017-11-15
Standard
J2383_201711
This SAE Recommended Practice establishes uniform Installation Parameters for desiccant Air Dryers for vehicles with compressed air systems.
CURRENT
2017-11-15
Standard
J840_201711
This SAE Recommended Practice covers equipment capabilities and the test procedure to quantify and qualify the shear strength between the friction material and backing plate or brake shoe for automotive applications. This SAE Recommended Practice is applicable to: bonded drum brake linings; integrally molded disc brake pads; disc brake pads and backing plate assemblies using mechanical retention systems (MRS); coupons from drum brake shoes or disc brake pad assemblies. The test and its results are also useful for short, semi-quantitative verification of the bonding and molding process.
CURRENT
2017-11-14
Standard
J2564_201711
The purpose of this SAE Information Report is to describe currently known automotive active stability enhancement systems, as well as identify common names which can be used to refer to the various systems and common features and functions of the various systems. The primary systems discussed are: a. ABS - Antilock Brake Systems b. TCS - Traction Control Systems c. ESC - Electronic Stability Control The document is technical in nature and attempts to remain neutral regarding unique features that individual system or vehicle manufacturers may provide.
CURRENT
2017-11-13
Standard
J2911_201711
This SAE Standard provides manufacturers/marketers, testing facilities and providers of technician training with a procedure for certifying compliance with the applicable standard. Manufacturers/marketers or sellers who advertise their products as Certified to an SAE J standard shall follow this procedure. Certification of a product is voluntary; however, this certification process is mandatory for those advertising meeting SAE Standard(s) requirements. Only certifying to this standard allows those claiming compliance to advertise that their product (unit), component, or service technician training meets all requirements of the applicable SAE standard.
CURRENT
2017-11-08
Standard
J2854_201711
The CRABI dummy was developed to evaluate small child restraint systems in automotive crash environments, in all directions of impact, with or without air bag interaction Basic anthropometry for this test device was taken from the University of Michigan Transportation Research Institute Report 85-23. Weight distribution and scaling methods for the infant were approved by the Society of Automotive (SAE) Infant Dummy Task Group. The dummy weighs 17.2 pounds and has a 26.4 inches standing or 17.3 inches sitting height. The Hybrid Ill-like neck and lumbar spine are laterally notched to reduce lateral stiffness The shoulders have flesh support for durability and human-like performance in areas where seatbelt webbing may be placed. In addition, rubber elements are used in each joint to improve biofidelity and to give the CRABI infant-like range of motion. The CRABI Six-Month-Old design meets all the SAE Infant Dummy Task Group anthropometry, biomechanical and instrumentation requirements.
CURRENT
2017-11-08
Standard
J1701M_201711
This SAE Information Report is provided as an advisory guide. Individual application discretion is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. The document covers a number of the variables in the torque-tension relationship: friction, materials, temperature, humidity, fastener and mating part finishes, surfaces, and the kind of tightening tools or equipment used.
CURRENT
2017-11-08
Standard
J1113/12_201711
This SAE Standard establishes test methods for the evaluation of devices and equipment in vehicles against transient transmission by coupling via lines other than the power supply lines. The test methods demonstrates the immunity of the instrument, device, or equipment to coupled fast transient disturbances, such as those caused by switching of inductive loads, relay contact bouncing, etc. Four test methods are presented in SAE J1113-12: 1.) The capacitive coupling clamp (CCC) method 2.) The direct capacitive coupling (DCC) method 3.) The inductive coupling clamp (ICC) method 4.) The capacitive/inductive coupling (CIC) method
CURRENT
2017-11-07
Standard
J551/5_201711
This SAE Recommended Practice specifies measurement procedures and performance levels for magnetic and electric field emissions and conducted power mains emissions over the frequency range 150 kHz to 30 MHz, for vehicles incorporating electric propulsion systems, e.g., battery, hybrid, or plug-in hybrid electric vehicles. Conducted emission measurements in this document are applicable only to battery-charging systems which utilize a switching frequency above 9 kHz, are mounted on the vehicle, and whose power is transferred by metallic conductors. Conducted emission requirements apply only during charging of the batteries from AC power lines. Conducted and radiated emissions measurements of battery-charging systems that use an induction power coupling device are not covered by this document. The measurement of electromagnetic disturbances for frequencies from 30 MHz to 1000 MHz is covered in CISPR 12.
CURRENT
2017-11-03
Standard
J2407_201711
Although not limited to, these installations are normally used on trucks considered as Medium Duty (Class 6 and 7), as well as Heavy Duty (Class 8).
CURRENT
2017-11-03
Standard
J772_201711
This SAE Recommended Practice is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances.
CURRENT
2017-11-03
Standard
J704_201711
The accompanying mounting and gear locations are applicable for all general installations of power take-off on the transmission gear box of motor trucks and tractors where the size of the transmission permits. The heavy-duty type opening can be adapted to the regular-duty type by the use of an adapter with 6.35 mm (0.25 in) flange thickness with appropriate bolt pattern and thread engagement. (See Figures 1 and 2.)
CURRENT
2017-11-03
Standard
J706_201711
This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for “free-spooling” may be provided and will be designed not to disengage itself under load. A drag brake may be provided to control “free-spooling,” but will not be relied on to control or hold a load.
CURRENT
2017-10-30
Standard
J2686_201710
This SAE Recommended Practice is intended for qualification testing for brake drums used on highway commercial vehicles with air brakes using an inertia-dynamometer procedure. This Recommended Practice consists of two distinct tests: Part A - durability and speed maintenance test, and Part B - heat check drag sequence test. Each test can be considered to be an independent evaluation of the brake drum which tests different properties.
CURRENT
2017-10-26
Standard
J2267_201710
This SAE standard applies to all forestry machines exposed to the hazard of objects penetrating the front of the operator station (other than the roof). This would include:
CURRENT
2017-10-25
Standard
J3087_201710
Develop and propose an SAE Recommended Practice for AEB system performance testing which: 1. Establishes uniform vehicle level test procedures 2. Identifies target equipment, test scenarios, and measurement methods 3. Identifies and explains the performance data of interest 4. Does not exclude any particular system or sensor technology 5. Identifies the known limitations of the information contained within (assumptions and "gap") 6. Intended to be a guide toward standard practice and is subject to change on pace with the technology 7. Limited to "Vehicle Front to Rear, In-lane Scenarios" for initial release
CURRENT
2017-10-25
Standard
J527_201710
This SAE Standard covers brazed double wall low-carbon steel tubing intended for general automotive, refrigeration, hydraulic, and other similar applications requiring tubing of a suitable quality for bending, flaring, beading, forming, and brazing.
CURRENT
2017-10-23
Standard
J393_201710
This SAE Recommended Practice establishes uniform engineering nomenclature for wheels, hubs, rims, and their components used in truck, bus, and trailer applications. This nomenclature and accompanying drawings are intended to define functional truck wheel, hub, and rim designs. For nomenclature specific to “passenger-type” disc wheels, refer to SAE J1982. The International Standard (ISO) nomenclature is shown in parentheses when different than SAE J393.
CURRENT
2017-10-18
Standard
J1939/84_201710
The purpose of this Recommended Practice is to verify that vehicles and/or components are capable of communicating a required set of information, in accordance with the diagnostic messages specified in SAE J1939-73, to fulfill the off-board diagnostic tool interface requirements contained in the government regulations cited below. This document describes the tests, methods, and results for verifying diagnostic communications from an off board diagnostic tool (i.e., scan tool) to a vehicle and/or component. SAE members have generated this document to serve as a guide for testing vehicles for compliance with ARB and other requirements for emissions-related on-board diagnostic (OBD) functions for heavy duty engines used in medium and heavy duty vehicles. The development of HD OBD regulations by US EPA and California’s Air Resources Board (ARB) require that diagnostic message services are exercised to evaluate diagnostic communication standardization requirements on production vehicles.
CURRENT
2017-10-18
Standard
MS1002_201710
See Table 1.
CURRENT
2017-10-18
Standard
J517_201710
This SAE Standard provides general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment. The general specifications contained in Sections 1 through 12 are applicable to all hydraulic hoses and supplement the detailed specifications for the 100R-series hoses contained in the later sections of this document (see Tables 1 and 2). This document shall be utilized as a procurement document only to the extent as agreed upon by the manufacturer and user. The maximum working pressure of a hose assembly comprising SAE J517 hose and hose connectors per SAE J516, SAE J518, SAE J1453, etc., shall not exceed the lower of the respective SAE maximum working pressure values. When using SAE J517 hose for marine applications, reference SAE J1475, SAE J1942, and SAE J1942-1. The SAE J517 100R9, 100R10, and 100R11 hoses are discontinued due to lack of demand. For DOD orders see Appendix C.
CURRENT
2017-10-13
Standard
J1939/5_201710
This document describes the application of the SAE J1939 recommended practices for compliance with on-board diagnostic malfunction detection system requirements for marine sterndrive and inboard spark ignition engines, as mandated by the California Air Resources Board (CARB). These Otto-cycle engines are not derived from automotive diesel-cycle engines.
CURRENT
2017-10-13
Standard
J1772_201710
This SAE Standard covers the general physical, electrical, functional and performance requirements to facilitate conductive charging of EV/PHEV vehicles in North America. This document defines a common EV/PHEV and supply equipment vehicle conductive charging method including operational requirements and the functional and dimensional requirements for the vehicle inlet and mating connector.
CURRENT
2017-10-12
Standard
J2613_201710
This SAE Standard covers sub-critically annealed or normalized electric resistance welded flash controlled single-wall high strength steel tubing intended for use in hydraulic pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, cold forming, welding and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path caused by the ID weld bead. Nominal reference working pressures for this tubing are listed in ISO 10763 for metric tubing and SAE J1065 for inch tubing. This specification also covers SAE J2613 Type-A tubing. The mechanical properties and performance requirements of standard SAE J2613 and SAE J2613 Type-A are the same. The designated differences of Type-A tubing do not imply that Type-A tubing is in anyway inferior to standard SAE J2613.
CURRENT
2017-10-12
Standard
J1270_201710
The force, torque, and power methods of measurement are all in common use and should yield the same test results. Effects of steering, traction, surface texture, and non-steady-state tire operations are excluded from the recommended practice because they are still in the research stage.
CURRENT
2017-10-12
Standard
J1402_201710
This recommended practice covers minimum requirements for air brake hose assemblies made from reinforced elastomeric hose and suitable fittings for use in automotive air brake systems including flexible connections from frame to axle, tractor to trailer, trailer to trailer and other unshielded air lines with air pressures up to 1 MPa, that are exposed to potential pull or impact. This hose is not to be used where temperatures, external or internal, fall outside the range of 40 to +100 °C.
CURRENT
2017-10-11
Standard
J1052_201710
This SAE Standard describes head position contours and procedures for locating the contours in a vehicle. Head position contours are useful in establishing accommodation requirements for head space and are required for several measures defined in SAE J1100. Separate contours are defined depending on occupant seat location and the desired percentage (95 and 99) of occupant accommodation. This document is primarily focused on application to Class A vehicles (see SAE J1100), which include most personal-use vehicles (passenger cars, sport utility vehicles, pick-up trucks). A procedure for use in Class B vehicles can be found in Appendix B.
CURRENT
2017-10-11
Standard
J2858_201710
This user's manual covers the Hybrid III 10-year old child test dummy. The manual is intended for use by technicians who work with this test device. It covers the construction and clothing, assembly and disassembly, available instrumentation, external dimensions and segment masses, as well as certification and inspection test procedures. It includes guidelines for handling accelerometers, guidelines for flesh repair, and joint adjustment procedures. Finally, it includes drawings for some of the test equipment that is unique to this dummy.
Viewing 1 to 30 of 8657

Filter

  • Range:
    to:
  • Year: