SAE Technical Standards

Viewing 1 to 50 of 11671
AC-9 Aircraft Environmental Systems Committee -
2015-05-29
ABSTRACT This SAE Aerospace Recommended Practice (ARP) defines recommended analysis and test procedures for qualification of pneumatically, electrically, manually, and hydraulically actuated air valve...
SAE TECHNICAL STANDARDS
AE-8A Elec Wiring and Fiber Optic Interconnect Sys Install -
2015-05-29
ABSTRACT This specification covers all aspects in electrical wire interconnection systems (EWIS) from the selection through installation of wiring and wiring devices and optical cabling and terminatio...
SAE TECHNICAL STANDARDS
AMS D Nonferrous Alloys Committee -
2015-05-28
ABSTRACT This specification covers an aluminum alloy in the form of sheet. This sheet has been used typically for structural parts requiring the strength of 2024-T3 and lower density, but usage is not...
SAE TECHNICAL STANDARDS
AMS G Titanium and Refractory Metals Committee -
2015-05-28
ABSTRACT This specification covers a titanium alloy in the form of seamless tubing.
SAE TECHNICAL STANDARDS
Lighting Materials Standards Committee -
2015-05-26
ABSTRACT This SAE Recommended Practice provides test methods and requirements to evaluate the suitability of plastic optical materials for possible use in discharge forward lighting (DFL) devices in m...
SAE TECHNICAL STANDARDS
AE-8C2 Terminating Devices and Tooling Committee -
2015-05-26
ABSTRACT SCOPE IS UNAVAILABLE.
SAE TECHNICAL STANDARDS
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies -
2015-05-26
ABSTRACT SCOPE IS UNAVAILABLE.
SAE TECHNICAL STANDARDS
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies -
2015-05-26
ABSTRACT SCOPE IS UNAVAILABLE.
SAE TECHNICAL STANDARDS
AMS F Corrosion Heat Resistant Alloys Committee -
2015-05-26
ABSTRACT This specification covers a corrosion and heat-resistant nickel alloy in the form of investment castings.
SAE TECHNICAL STANDARDS
G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies -
2015-05-26
ABSTRACT SCOPE IS UNAVAILABLE.
SAE TECHNICAL STANDARDS
AMS K Non Destructive Methods and Processes Committee -
2015-05-26
ABSTRACT This specification covers two types of refined hydrocarbon compounds in the form of liquids.
SAE TECHNICAL STANDARDS
AMS D Nonferrous Alloys Committee -
2015-05-26
ABSTRACT This specification specifies the engineering requirements for heat treatment, by part fabricators (users) or their vendors or subcontractors, of parts (See 8.8.1). It also covers heat treatme...
SAE TECHNICAL STANDARDS
AMS B Finishes Processes and Fluids Committee -
2015-05-21
ABSTRACT This SAE Standard specifies the requirements for the electro-deposition of zinc on non-corrosion resisting steel items for protection against corrosion, and on copper-base alloy items and cor...
SAE TECHNICAL STANDARDS
AMS B Finishes Processes and Fluids Committee -
2015-05-21
ABSTRACT This SAE Standard specifies the requirements for the electro-deposition of cadmium on non-corrosion resisting steel items for protection against corrosion, and on copper based alloy items and...
SAE TECHNICAL STANDARDS
AMS B Finishes Processes and Fluids Committee -
2015-05-21
ABSTRACT This SAE Standard specifies the requirements for the nickel-plating of ferrous metals, copper alloys, aluminum alloys and zinc alloys for one or more of the following purposes: a. the product...
SAE TECHNICAL STANDARDS
AMS B Finishes Processes and Fluids Committee -
2015-05-21
ABSTRACT This SAE Standard covers the requirements for coatings of high purity aluminum on low alloy steels, high strength steels, corrosion-resisting steels, aluminum alloys and titanium alloys and o...
SAE TECHNICAL STANDARDS
AMS B Finishes Processes and Fluids Committee -
2015-05-21
ABSTRACT This SAE Standard covers the requirements for the deposition of cadmium coatings on carbon steel, low alloy steels, high strength steels, corrosion resisting steels and other materials where ...
SAE TECHNICAL STANDARDS
AMS B Finishes Processes and Fluids Committee -
2015-05-21
ABSTRACT This SAE Standard specifies the properties of sulphuric acid anodizing of aluminum and aluminum alloys.
SAE TECHNICAL STANDARDS
2015-05-21
This product includes information on the manufacturer, engine, applications, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and ...
SAE TECHNICAL STANDARDS
2015-05-21
This product includes information on the manufacturer, engine, application, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and t...
SAE TECHNICAL STANDARDS
Hybrid - EV Committee -
2015-05-19
ABSTRACT This SAE Standard J3072 establishes interconnection requirements for a utility-interactive inverter system which is integrated into a plug-in electric vehicle (PEV) and connects in parallel w...
SAE TECHNICAL STANDARDS
G-14 Americas Aerospace Quality Standards Committee (AAQSC) -
2015-05-19
ABSTRACT This standard defines uniform quality and technical requirements relative to metallic parts marking performed using "data matrix symbology" within the aviation, space, and defense industry. I...
SAE TECHNICAL STANDARDS
AE-8C2 Terminating Devices and Tooling Committee -
2015-05-14
ABSTRACT SCOPE IS UNAVAILABLE.
SAE TECHNICAL STANDARDS
AMS P Polymeric Materials Committee -
2015-05-13
ABSTRACT This specification covers an unpigmented grade of vinyl plastic, unfilled and not containing plasticizer, in the form of sheet and film.
SAE TECHNICAL STANDARDS
AMS P Polymeric Materials Committee -
2015-05-13
ABSTRACT This specification covers a silica fiber insulation in the form of felted pads, flat or in rolls, as ordered.
SAE TECHNICAL STANDARDS
AMS P Polymeric Materials Committee -
2015-05-13
ABSTRACT This specification covers one grade of polytetrafluoroethylene (PTFE) resin in the form of film and film tape.
SAE TECHNICAL STANDARDS
AMS P Polymeric Materials Committee -
2015-05-13
ABSTRACT This specification covers a highly filled epoxy potting compound supplied as a two-component system.
SAE TECHNICAL STANDARDS
AMS P Polymeric Materials Committee -
2015-05-13
ABSTRACT This specification covers a filled epoxy resin formulation, supplied as a one-component system, requiring an oven cure for attainment of its properties.
SAE TECHNICAL STANDARDS
AMS P Polymeric Materials Committee -
2015-05-13
ABSTRACT This specification covers polyfluoroethylenepropylene in the form of film and sheet 0.020 inch (0.51 mm) and under in nominal thickness. These products have been used typically for electrical...
SAE TECHNICAL STANDARDS
AMS P Polymeric Materials Committee -
2015-05-13
ABSTRACT This specification covers one grade of polytetrafluoroethylene resin in the form of film.
SAE TECHNICAL STANDARDS
AMS P Polymeric Materials Committee -
2015-05-13
ABSTRACT This specification covers one grade of polytetrafluoroethylene (PTFE) resin in the form of film, normally produced by skiving. This film has been used typically for gaskets and other parts fo...
SAE TECHNICAL STANDARDS
AMS P Polymeric Materials Committee -
2015-05-13
ABSTRACT This specification covers alumina-silica, glass, and other ceramic fiber thermal insulation in the form of felt and fabric flat sheets, rolls, or molded non-pliable blocks. Nominal thickness ...
SAE TECHNICAL STANDARDS
AMS P Polymeric Materials Committee -
2015-05-13
ABSTRACT This specification covers resin-bonded glass fibers in the form of felted pads, flat or in rolls.
SAE TECHNICAL STANDARDS
Marine Technical Steering Committee -
2015-05-12
ABSTRACT This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other...
SAE TECHNICAL STANDARDS
Marine Technical Steering Committee -
2015-05-12
ABSTRACT This SAE Standard specifies basic tolerances and dimensions for inboard propeller-shaft ends, propeller hubs and keyways for shaft sizes 3/4 in (19 mm) through 8 in (203 mm).
SAE TECHNICAL STANDARDS
Truck and Bus Wheel Committee -
2015-05-12
ABSTRACT This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for truck and bus applications. Disc wheels designed only for singl...
SAE TECHNICAL STANDARDS
Ship Fluid Systems Committee -
2015-05-12
ABSTRACT This Information Report provides a description of bleed-air pneumatic system elements and identifies parameters required to define the requirements for a detailed specification. Specific desi...
SAE TECHNICAL STANDARDS
Truck Bus Control and Communications Network Committee -
2015-05-12
ABSTRACT This document is intended to supplement the J1939 documents by offering the J1939 information in a form that can be sorted and search for easier use. The J1939 Digital Annex, introduced in Au...
SAE TECHNICAL STANDARDS
AMS G9 Aerospace Sealing Committee -
2015-05-11
ABSTRACT This specification covers a permanently mastic, non-curing fluorosilicone sealing compound in the form of a paste.
SAE TECHNICAL STANDARDS
A-20A Crew Station Lighting -
2015-05-07
ABSTRACT This document defines the method for voltage identification by the use of color-coded insulators at the base of the lamps. Table 1 shows the design volts and corresponding insulator colors. T...
SAE TECHNICAL STANDARDS
A-5A Wheels, Brakes and Skid Controls Committee -
2015-05-07
ABSTRACT This document recommends supplementary design criteria to enhance endurance and reliability of transport aircraft wheels and brakes.
SAE TECHNICAL STANDARDS
Interior Climate Control MAC Supplier Committee -
2015-05-07
ABSTRACT The intent of this standard is to establish a framework to assure that all evaporators for R-744, R-1234yf, and R-445A mobile air conditioning (MAC) systems meet appropriate testing and label...
SAE TECHNICAL STANDARDS
Dummy Testing and Equipment Committee -
2015-05-07
ABSTRACT This procedure establishes a recommended practice for performing a Low Speed Knee Slider test to the Hybrid III 50th Male Anthropomorphic Test Device (ATD or crash dummy). This test was creat...
SAE TECHNICAL STANDARDS
Brake Linings Standards Committee -
2015-05-07
ABSTRACT This procedure describes a method for generating, preparing and analyzing samples of new and unused brake friction materials for their chemical constituents.
SAE TECHNICAL STANDARDS
Vehicular Flat Panel Display Standards Committee -
2015-05-07
ABSTRACT The scope of this SAE Standard is to provide methods to determine display optical performance in all typical automotive ambient light illumination - with focus on High Ambient Contrast Ratio,...
SAE TECHNICAL STANDARDS
AMS F Corrosion Heat Resistant Alloys Committee -
2015-05-07
ABSTRACT This specification covers a corrosion resistant steel in the form of sheet, strip, and plate.
SAE TECHNICAL STANDARDS
Hybrid - EV Committee -
2015-05-07
ABSTRACT This SAE Information Report J2836/5™ establishes the use cases for communications between Plug-In Electric Vehicles (PEV) and their customers. The use case scenarios define the information to...
SAE TECHNICAL STANDARDS
AE-8C2 Terminating Devices and Tooling Committee -
2015-05-07
ABSTRACT This specification covers environment resistant, heat-shrinkable solder type shield terminations. They may be used on data-bus, RF and shielded cables in applications where the operating temp...
SAE TECHNICAL STANDARDS
Functional Safety Committee -
2015-05-07
ABSTRACT This SAE Recommended Practice presents a method and example results for determining the Automotive Safety Integrity Level (ASIL) for automotive electrical and electronic (E/E) systems. This a...
SAE TECHNICAL STANDARDS
AMS D Nonferrous Alloys Committee -
2015-05-06
ABSTRACT This specification covers the specific requirements for aluminum alloy 6061 bar, rod, shapes, tube, and wire produced by extrusion.
SAE TECHNICAL STANDARDS
Viewing 1 to 50 of 11671