 |
Hydraulic fluids2013-05-13
This specification establishes the design, performance, and test requirements for hydraulic flow rate fuses intended to be used for hydraulic circuit protection.
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
2013-05-05
This AIR provides descriptions of aircraft actuation system failure-detection methods. The methods are those used for ground and in-flight detection of failures in electrohydraulic actuation systems ...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
2013-04-30
This SAE Aerospace Standard (AS) specifies the general requirements for hydraulic system reservoirs that are installed in commercial and military aircraft and helicopters and also in missile hydraulic...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
2013-04-22
This SAE Aerospace Information Report (AIR) presents data on normally accepted changes in physical properties and contamination levels for military hydraulic fluids used in hydraulic test stands. This...
SAE TECHNICAL STANDARDS
2013-04-22
This SAE Aerospace Recommended Practice (ARP) defines impulse test procedures that are recommended for hydraulic components.
SAE TECHNICAL STANDARDS
2013-03-11
This Aerospace Recommended Practice (ARP) provides general requirements for a generic rudder and brakes pedal unit that could be used for Fly by Wire transport and business aircraft. It addresses the ...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
2013-02-13
This SAE Recommended Practices specifies a procedure for determining structural strength and fatigue life of disc-brake caliper assemblies which are satisfactory for vehicle usage. It is applicable t...
SAE TECHNICAL STANDARDS
2013-02-11
To describe laboratory methods for determining and reporting the contaminant level of the wetted portion of hydraulic fluid power components, parts, subsystems and systems, and of fill fluids. For ea...
SAE TECHNICAL STANDARDS
2013-02-10
The purpose of this document is to develop the general characteristics and requirements for feel-force control systems for active cockpit controllers, also known as Active Inceptors. The document pres...
SAE TECHNICAL STANDARDS
2013-01-21
This SAE Aerospace Recommended Practice (ARP) is intended as a guide to aid in the specification and testing of Direct Drive Servovalves, but does not include the associated electronic controller.
Th...
SAE TECHNICAL STANDARDS
2012-12-19
This document establishes recommended practices for the specification of general performance, design, test, development, and quality assurance requirements for the flight control related functions of ...
SAE TECHNICAL STANDARDS
2012-11-15
Shortly after World War II, as aircraft became more sophisticated and power-assist, flight-control functions became a requirement, hydraulic system operating pressures rose from the 1000 psi level to ...
SAE TECHNICAL STANDARDS
2012-11-01
This SAE Aerospace Recommended Practice (ARP) provides guidelines for the configuration and design of mechanical control signal transmission systems and subsystems. It is focused on the recommended pr...
SAE TECHNICAL STANDARDS
2012-10-02
To provide a method by which to assess the cleanliness of new hydraulic fluids. The method is applicable to new mineral and synthetic hydraulic fluids - regardless of packaging. This SAE Standard is ...
SAE TECHNICAL STANDARDS
2012-09-24
This SAE Aerospace Information Report (AIR) discusses the design choices and engineering trade-offs available to the system designer in the efficient selection and application of Last-Chance filters i...
SAE TECHNICAL STANDARDS
2012-09-24
This SAE Aerospace Information Report (AIR) discusses the terminology, types, method of manufacture and chemistry of the fine wire meshes used for filtration of hydraulic, lubrication fuel systems, an...
SAE TECHNICAL STANDARDS
2012-09-24
This Aerospace Information Report (AIR) describes a mathematical model that can be used to analyze particle count data. Particle counts that fit the model can be graphically displayed, converted from ...
SAE TECHNICAL STANDARDS
2012-08-23
Most of the Trimmable Horizontal Stabilizer Actuators (THSA) feature a dual structural load path, the primary load path being loaded, the secondary load path being normally unloaded, or both load path...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
2012-08-20
This SAE Information Report is primarily to familiarize the designer of hydraulic powered machinery with the necessity for oil filtration in the hydraulic power circuit, the degree of system cleanline...
SAE TECHNICAL STANDARDS
2012-07-31
This SAE Aerospace Recommended Practice (ARP) provides general requirements for a generic “passive” side stick that could be used for fly by wire transport and business aircraft. It addresses the foll...
SAE TECHNICAL STANDARDS
2012-07-24
This specification establishes the design, performance, and test requirements for hydraulic quantity measuring fuses intended to be used for hydraulic circuit protection.
SAE TECHNICAL STANDARDS
2012-06-04
This document sets forth recommendations of SAE Subcommittee A-6B (Fluid Power Sources) relative to the procedure and methods to be used in the obtaining and evaluation of filter patch tests for aeros...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
2012-05-29
This SAE Recommended Practice has been formulated to advance and endorse the use of the ISO (International Organization for standardization) Solid Contaminant Code as the universal means for expressin...
SAE TECHNICAL STANDARDS
2012-02-23
This SAE Aerospace Standard (AS) defines cleanliness classes for particulate contamination of hydraulic fluids and includes methods of reporting related data (Appendix A). The contamination classes se...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
2012-01-19
This SAE Aerospace Standard (AS) defines the materials, apparatus and procedure for sizing and counting of particulate contamination, 5 µm or greater, in hydraulic fluid samples by membrane filtratio...
SAE TECHNICAL STANDARDS
2011-12-19
The purpose of this test procedure is to present test methods that can be utilized to evaluate the filtration and operating characteristics of filters that will be utilized in a cryogenic system. The...
SAE TECHNICAL STANDARDS
2011-12-12
This SAE Aerospace Information Report (AIR) contains Lessons Learned from aerospace actuation, control and fluid power systems technologies. The lessons were prepared by engineers from the aerospace i...
SAE TECHNICAL STANDARDS
2011-09-21
The scope of the project it to develop a comprehensive description document that displays various examples of aircraft systems driving Trimmable Horizontal Stabilizers.
The main focus is on mechanica...
SAE TECHNICAL STANDARDS
2011-06-17
This SAE Recommended Practice identifies general requirements for hydraulic fluids to be used for ship systems and equipment with respect to power transmission, lubrication, and passive applications...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
2011-05-16
This ARP details the recommended tests and their associated test means for aircraft hydraulic systems at the system level that are required to demonstrate compliance with 14CFR Part 25 and EASA CS 25 ...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
2011-04-19
Establish a uniform specification for reference usage in specific documents, such as fluid power component test procedures, where a fluid designation is required.
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
2011-02-15
This ARP provides a comprehensive and consistent set of guidelines for the definition, recognition,
troubleshooting and repair of hydraulic components and systems on in-service commercial aircraft
a...
WIP- Not available for purchase at this time
SAE WORK IN PROGRESS TECHNICAL STANDARDS
2011-02-11
This SAE Aerospace Information Report (AIR) discusses the nature, method of manufacture and chemistry of fine wire meshes of the type used for filtration and similar applications, and how this informa...
SAE TECHNICAL STANDARDS
2011-02-08
This document discusses the relative merits of the physical and chemical properties of hydraulic fluids in relation to the aerospace hydraulic system design, and the related materials compatibility. ...
SAE TECHNICAL STANDARDS
2010-10-14
The Society of Automotive Engineers (SAE) Industrial Lubricants
Committee has developed a number of industrial, non-production,
lubricant performance specifications. The purpose of this voluntary SAE...
SAE TECHNICAL STANDARDS
2010-06-21
ISO 7745 shall be used for providing detailing, operational characteristics, advantages, disadvantages, and factors affecting the choice to be made among fire-resistant fluids.
SAE TECHNICAL STANDARDS
2010-05-26
this SAE Aerospace Recommended Practice (ARP) describes two procedures for sampling particles in dust controlled spaces. One procedure covers airborne dust above 5 µm. The other (and newly added pro...
SAE TECHNICAL STANDARDS
2010-05-04
This document is to be used as a guide in preparing specifications for maintenance and inspection of acme screw assemblies used in driven linear actuators. It is intended to cover Acme screw assembli...
SAE TECHNICAL STANDARDS
2010-03-08
This SAE Aerospace Recommended Practice (ARP) provides procedures for assuring cleanliness of sampling equipment, for performing the sampling process, and for measuring and reporting the sample partic...
SAE TECHNICAL STANDARDS
2009-01-22
This SAE Recommended Practice defines a procedure, which will aid in assessing the contaminant sensitivity of hydraulic valves. The approach taken defines a test procedure with flexibility for testin...
SAE TECHNICAL STANDARDS
2009-01-06
This document has been declared "CANCELLED" as of January 2009 and has been superseded by ARP4150. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards ...
SAE TECHNICAL STANDARDS
2008-07-15
An industry survey has been completed to determine the incidence of jam and excessive backlash in rotary and linear mechanical actuators subject to ¿primary flight control like¿ duty cycles. The data...
SAE TECHNICAL STANDARDS
2008-02-21
Scope unavailable.
SAE TECHNICAL STANDARDS
2008-02-07
This SAE Aerospace Recommended Practice (ARP) establishes the requirements for the design, manufacture, and qualification of four hydraulic switching valves used in airborne applications. Two are pres...
SAE TECHNICAL STANDARDS
2006-11-13
This SAE Recommended Practice defines a procedure, which will aid in assessing the contaminant sensitivity of hydraulic valves. The approach taken defines a test procedure with flexibility for testin...
SAE TECHNICAL STANDARDS
2006-11-13
This SAE Recommended Practice identifies general requirements for hydraulic fluids to be used for ship systems and equipment with respect to power transmission, lubrication, and passive applications...
SAE TECHNICAL STANDARDS
2005-05-02
This SAE Aerospace Standard (AS) defines cleanliness classes for particulate contamination of hydraulic fluids and includes methods of reporting related data (Appendix A). The contamination classes se...
SAE TECHNICAL STANDARDS
2005-02-16
This SAE Aerospace Standard (AS) specifies the general requirements for hydraulic system reservoirs that are installed in commercial and military aircraft and helicopters and also in missile hydraulic...
SAE TECHNICAL STANDARDS
2004-08-04
This specification covers hand driven, hydraulic ram pumps used on type I (-65° to +160°F) aircraft hydraulic systems.
SAE TECHNICAL STANDARDS
2004-08-04
This specification presents the standard method for the proof testing and prestretching of aircraft cable assemblies.
SAE TECHNICAL STANDARDS
|
Available Standards ProductsResources
General Information |
©2013 SAE International. All Rights Reserved.
