 |
Aerospace - SAE Technical Standards WIP2012-05-23
The complete requirements for procuring the product shall consist of this document and the latest Issue of the basic specification, AMS2431.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-23
This SAE Aerospace Recommended Practice establishes the requirements and procedures for eddy current detection of surface cracks in aerospace structures.
Procedures for eddy current inspection of op...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-21
This document, as referenced in the applicable product specifications in procurement documents, contains: a. A catalog of the standard carbon steels, alloy steels (including H-steels), and stainless ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-18
This Aerospace Recommended Practice contains useful guidance regarding hardware design and installation procedures. This type of information is usually not included in SAE seal gland standards but is ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-15
In lieu of TSO-C135, this SAE Aerospace Standard (AS) prescribes the minimum performance standards for wheels, brakes, and wheel and brake assemblies using electric power actuation for transport categ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-14
A life support system (LSS) is usually defined as a system that provides elements necessary for maintaining human life and health in the state required for performing a prescribed mission. The LSS, d...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-13
Scope unavailable.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-13
No scope available.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-13
No scope available.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-13
No scope available.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-13
This procurement specification covers bolts and screws made from a corrosion and heat resistant age hardenable nickel base alloy of the type identified under the Unified Numbering System as UNS N07...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-13
No scope available.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-11
No abstract available
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-10
This SAE Aerospace Standard (AS) covers batch qualification procedure for virgin and compounded polytetrafluoroethylene (PTFE) resins used for compression molding. AS9100 requires virgin and modified ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-10
This specification covers a synthetic rubber sealing compound which is electrically conductive when used in a faying surface, contains corrosion inhibitors, and supplied as a two-component system whic...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-09
The specific purpose of this AIR is to provide general background information to better acquaint those who are involved with ramp de-icing of aircraft. Because of the wide variance of atmospheric cond...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-09
This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-09
This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, and molded shapes.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-09
This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-08
No Scope Available
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-08
Scope unavailable.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-08
Scope unavailable.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-08
A photographic technique is described for determining minimum observer-to-aircraft distances during acoustic "fly-over" tests. Possible sources of error are discussed, and it is shown that with ordina...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-08
To ensure success in design of elastomeric parts for use at low temperature, the design engineer must understand the peculiar properties of rubber materials at these temperatures. There are no static...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-08
This specification covers a standard fluorosilicone (FVMQ) rubber stock in the form of molded test slabs.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-08
This specification covers a standard chloroprene (CR) rubber stock in the form of molded test slabs.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-07
This specification covers a fluorocarbon (FKM) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-07
This specification covers manufacturing tolerances applicable to seamless and welded tubing of corrosion and heat-resistant steel ordered to inch dimensions. These tolerances apply to all conditions a...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-07
This specification covers a fluorocarbon (FKM) rubber in the form of sheet, strip, tubing, extrusions and molded shapes.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-04
This specification covers a nickel-aluminum bronze alloy in the form of sand or centrifugal castings. <p>hese castings have been used typically for parts requiring a combination of high strength...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
Contacts, Electrical Connector, Pin, Crimp Removable, Shielded (For MIL-C-26482 Series 1 Connectors)
2012-05-03
No scope available.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-03
No scope available.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-03
No scope available.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-03
No scope available.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-03
This specification covers a low-outgassing silicone (PVMQ) rubber compound in the form of molded rings. Primarily for use in interplanetary space and other hard vacuums from -75 degrees to +150 degre...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-02
No scope available.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-02
This specification covers the design requirements and all performance requirements for procurement of 1 7/8 inch dial pilot's standby compasses as specified herein.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-02
No scope available.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-02
To specify minimum requirements for non-magnetic gyroscopically stabilized direction indicators for use in aircraft, the operation of which may subject the instruments to the environmental conditions ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-02
To specify minimum requirements for gyroscopically stabilized Magnetic Direction Instruments for use in aircraft, the operation of which may subject the instruments to the environmental conditions spe...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-02
This standard establishes the essential minimum safe performance requirements for flight director instruments, primarily for use with turbine-powered transport aircraft, the operation of which may sub...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-02
To specify minimum requirements for Fuel Flowmeters for use primarily in reciprocating engine powered civil transport aircraft, the operation of which may subject the instruments to the environmental ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-02
No scope available.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-02
This specification covers design requirements and all performance requirements for the procurement of single and dual hermetically sealed, integrally lighted, remote indicating, pressure indicators.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-02
This specification covers the design and performance requirements for a single axis, four load-factor level counting accelerometer group referred to hereafter as "equipment."
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-02
To specify minimum requirements for Automatic Pilots primarily for use in reciprocating engine powered civil transport aircraft, the operation of which may subject the instruments to the environmental...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-02
This specification covers a titanium alloy in the form of prealloyed powder. This powder has been used typically for compaction into net or near net shapes and into forging stock in the form of billet...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-02
This Aeronautical Standard covers two basic types of instruments as follows: Type I - Float Instruments, Type II - Capacitance Instruments. To specify minimum requirements for Fuel and Oil Quantity In...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-05-01
No scope available.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
|
Available Standards ProductsResources
General Information |
©2012 SAE International. All Rights Reserved.
