 |
Automotive - SAE Technical Standards WIP2013-06-13
The methods included in this document are:
a. Voltage-Temperature Design Margins.
b. Voltage Interruptions and Transients.
c. Voltage Dropouts and Dips.
d. Current Draw Under a Number of Conditions....
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-06-04
Develop new AS standard for a two bolt strap clamp for use on engine high temperature air systems. Sizes -16 thru -80, similar to GE's 9134M25. Material 625 Nickel Alloy.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-28
This SAE Recommended Practice establishes a uniform test procedure for evaluating performance of operator enclosure pressurization systems for construction, general-purpose industrial, agricultural, ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-23
SAE J1939-03 provides requirements and guidelines for the implementation of On Board Diagnostics (OBD) on heavy-duty vehicles (HDV) using the SAE J1939 family of standards. The guidelines identify whe...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-21
This document specifies minimum performance and durability requirements for satisfactory vehicle usage, and it is applicable to wheel cylinder assemblies from commercial production, after production s...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-20
This document provides a method/ procedure for specifying the properties of vulcanized elastomeric materials (natural rubber or synthetic rubbers, alone or in combination) that are intended for, but n...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-20
This classification system tabulates the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-17
The scope of the SAE Heated Seat Committee is to develop a recommended practice to promote an acceptable operating condition for heated vehicle seats. The design guidelines are established in order to...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-15
This SAE Standard includes complete general and dimensional specifications for those types of pipe, filler, and drain plugs (shown in Figures 1 to 6 and Tables 1 to 4) commonly used in automotive and ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-13
Basic Methods--The force, torque, and power methods of measurement are all in common use and should yield the same test results. Effects of steering, traction, surface texture, and non-steady-state t...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-13
This SAE Recommended Practice sets forth a method for testing and evaluating the paintable characteristics of automotive sealers. this document contains three samples preparation procedures: Method 1 ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-13
The purpose of this SAE Information Report is to compare the results of Florida exposure at 45 deg from the horizontal, facing south, with those at deg from the horizontal, facing south, using variou...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-13
This SAE Recommended Practice establishes a uniform procedure for testing the brake systems (service and parking) of all passenger cars, light-duty trucks, and multipurpose passenger vehicles up to an...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-10
This SAE RP provides a set of test methods and practices for the characterization of the properties of Li-battery electrolyte.
It is not within the scope of this document to establish criteria for ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-07
This SAE Recommended Practice provides minimum performance requirements and uniform procedures for nut seat system strength of wheels intended for normal highway use on passenger cars, light trucks, (...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-06
These recommended practices provide general recommendations for designing and fabricating metallic tubes and tube assemblies for fluid power applications utilizing commonly available manufacturing met...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-06
This SAE standard recommends the use of ISO 19879 to perform various types of tests to evaluate functional performance requirements for carbon and steel alloy tube conductor assemblies for hydraulic f...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-06
This SAE Recommended Practice is applicable to all liquid-to-gas, liquid-to-liquid, gas-to-gas, and gas-to-liquid heat exchangers used in vehicle and industrial cooling systems. This document outline...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-04
The purpose of this SAE Information Report is to describe currently known automotive active stability enhancement systems, as well as identify common names which can be used to refer to the various s...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-01
The product for which data is to be available is for class 6 and larger, i.e., gross vehicle weight \mg 9.6 kg (19500 lb). The objective is to establish a set of data requirements which powertrain c...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-26
This SAE Recommended Practice promotes uniformity in the evaluation and qualification tests conducted on DIG fuel injectors used in gasoline engine applications. The document scope is limited to elect...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-24
This test code establishes wheel-slip brake-control system capabilities with regard to: 1.1 vehicle stability, maneuverability, and system function on various road surface conditions, including varia...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-20
This SAE Standard covers general and dimensional specifications for the Code 62 metric (type 1) and inch (type 2) flanged heads, flange clamps (FC and FCM), and split flange clamps (FCS & FCSM) applic...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-19
The purpose of this SAE Recommended Practice is to define criteria of performance for an optical data channel when numerical time and space data are taken from the images to analyze impact test result...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-19
In order to compare test results obtained from different crash test facilities, standardized coordinate systems need to be defined for crash test dummies, vehicle structures, and laboratory fixtures. ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-18
The purose of this test is to evaluate the axial strength of the nut seat of wheels intended for use on passenger cars, light trucks, and multipurpose vehicles. In addition, a minimum contact area is...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-18
This standard covers ultra thin wall low voltage primary cable intended for use at a nominal system voltage of 60 V DC (60 V AC rms) or less in surface vehicle electrical systems. The tests are intend...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-18
This standard covers low voltage primary cable intended for use at a nominal system voltage of 60 V DC (25 V AC) or less in surface vehicle electrical systems. The tests are intended to qualify cable...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-18
This SAE Recommended Practice establishes minimum performance requirements and related uniform laboratory test procedures for evaluating axial (lateral) curb impact collision properties of all wheels ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-12
This SAE Recommended Practice covers recommended practices for design and evaluation of hose clamped joints primarily in automotive applications. It is intended to: (a) evaluate current joint designs...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-02
The purpose of this document is to define design, construction, operational, and maintenance requirements for hydrogen fuel storage and handling systems in on-road vehicles. Performance-based require...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-28
Create AS Part Standard AS5790 for Adapter Fitting, Ring Locked, Beam Seal, 4000 PSI, Similar to AS1986, Except Material is A286 CRES with Solid Film Lube.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-27
The special risks associated with conducting crash tests on EV’s and HEV’s can be divided into two main categories, risk of electrocution, and risk of fire/explosion. Procedures to ensure protection f...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-26
This SAE Standard provides test procedures, requirements, and guidelines for clearance, sidemarker, and identification lamps intended for use on vehicles 2032 mm or more in overall width. A clearance...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-26
This SAE Standard describes guarding to help prevent hazardous machine movement caused by activation of the starter motor by bypassing the starter control system. This document is applicable to off-r...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-25
This SAE Recommended Practice covers power transfer units (PTUs) used in passenger car and light truck applications. PTUs may be of the chain, geared, single- or multi-axis type and may incorporate a ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-14
Provide recommendations on battery testing so as define boundary conditions in order to yield data useful for modeling.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-14
This information report provides an overview of a typical high voltage xEV and the associated safety systems typically employed by OEM’s to protect these high voltage systems. The report aims to imp...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-14
This SAE Recommended Practice describes a cross peel test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber-reinforced plastics to themselves and t...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-14
The material desired under this recommended practice is a synthetic resin plastic sealer of the nondrying, nonbleeding, and noncorrosive type that may be extruded to the specified size and used as a m...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-12
This SAE Standard is used to determine the exterior A-weighted equivalent sound power level of static and in-place dynamic machines (dozer, loader, excavator, and backhoe) similar to the sound power o...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-12
This practice applies to engine cooling fans used on Off-Road Work Machines and related equipment defined in SAE J1116 MAR99. It does not include guarding for belts, pulleys, or other rotating equipm...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-08
This SAE Recommended Practice provides procedures and methods for testing service, spring applied parking, and combination brake actuators with respect to durability, function, and environmental perfo...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-07
This AIR provides an overview of several emerging technologies for on board oxygen generation. It complements AIR 825/6, which covers pressure swing adsorption using zeolite molecular sieve beds to c...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-07
This document describes technical approaches that can be applied to show that proposed oxygen equipment and systems achieve suitable oxygenation in users. These approaches can be used to demonstrate ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-05
This SAE Standard provides test procedures, requirements, and guidelines for tail lamps (rear position lamps) intended for use on vehicles of less than 2032mm in overall width.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-05
This document will primarily address intrinsic reliability of electronic components for use in automotive electronics. Where practical, methods of extrinsic reliability detection and prevention will a...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-04
This recommended practice aims to establish a common format for displaying and presenting crash-related data recorded and stored within certain electronic components currently installed in many light-...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-02-27
This SAE Standard covers cold drawn and annealed seamless low-carbon steel pressure tubing intended for use as hydraulic lines and in other applications requiring tubing of a quality suitable for flar...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-02-27
This SAE Standard covers normalized electric-resistance welded, cold-drawn, single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
|
Available Standards ProductsResources
General Information |
©2013 SAE International. All Rights Reserved.
