 |
Commercial Vehicle - SAE Technical Standards WIP2013-06-10
This SAE Recommended Practice provides test procedures and performance requirements for all-terrain vehicle headlamps.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-06-10
This Hydrospace Information Report (HIR) is intended to provide basic design considerations with respect to bleed-air pneumatic systems for marine craft equipped with gas turbine propulsion engines or...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-30
This document is intended to supplement SAE J2403 by providing the content of Table 1, Table 2, and Table 3 from SAE J2403 in a form that can be sorted and searched for easier use. It is NOT intended ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-23
This SAE Recommended Practice is applicable to all E/E systems on MD and HD vehicles. The terms defined are largely focused on compression-ignited and spark-ignited engines. Specific applications of t...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-15
This SAE Recommended Practice describes the dynamic and static testing procedures required to evaluate the integrity of an equipment mount device or system when exposed to a frontal or side impact (i....
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-15
This SAE Recommended Practice describes the test procedures for conducting frontal impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-05-01
The purpose of this document is to provide dimensions of clearance envelopes for various types of six-bolt regular-duty, eight-bolt heavy-duty, and side- and rear-mounted truck transmission power take...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-30
This SAE Standard establishes the minimum performance and endurance requirements for coiled air brake tubing assemblies used for hookup between tractors, trailers and converter dollies. The Standards...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-30
This document establishes the following criteria for electrically operated forward warning horns on mobile construction machinery: (a) Forward warning horn performance requirements; (b) Measurement te...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-26
This SAE Standard applies to all types of heavy-duty storage batteries for use on off-road machines as described in SAE J1116. Included are definitions of industry terms, test procedures, general re...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-25
This recommended practice is to assist in the development of Technical Publications which will stress injury prevention and uniformity of format and content. This recommended practice is intended to ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-17
This SAE Recommended Practice establishes performance guidelines of the air reservoir systems used on trucks, towing trucks, truck-tractors, trailers, and converter dollies, with GVWRs over 10 000 lb,...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-17
This SAE Recommended Practice provides instructions and test procedures for air braked vehicles including but not limited to trucks, truck-tractors, trailers, dollies, and buses used on highways but d...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-08
This SAE Recommended Practice provides a field test procedure and instructions for: Instrumentation and Equipment Vehicle Preparation Test of air-braked single and combination vehicles Calculation of ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-04-05
This SAE Recommended Practice establishes performance guidelines for the threshold pressure and brake force output of the brakes on the axles of air braked towing trucks, truck-tractors, truck-trailer...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-19
This analysis applies to crane types as covered by Power crane and shovel Association Standard Number Two, Mobile Hydraulic Crane standards and ANSI B30.15; refer to 5.1. This calculation method has b...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-15
This standard specifies dimensions for cutting edge cross section. This standard is for cutting edge sections typically used in earthmoving machinery defined in SAE J1507: a. Tractor - Scrapers ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-15
This SAE Standard is intended to improve operator efficiency and convenience by providing guidelines for the uniformity of location and direction of motion of operator controls used on industrial whee...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-13
The purpose of this SAE Information Report is to provide concepts for rational selection and application of materials for Rollover Protective Structures (ROPS) and Falling Object Protective Structures...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-11
To provide uniform laboratory procedures and radial/lateral load pairs for biaxial fatigue testing of disc wheel intended for normal highway use on trucks, buses, and trailers applicable for the North...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-08
This procedure provides test performance requirements for service, spring applied parking, and double diaphragm combination air brake actuators with respect to durability, function, and environmental ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-07
This SAE Standard specifies minimum performance and test criteria for brake systems to enable uniform assessment of the braking capability of walk-along self-propelled work machines with a mass greate...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-03-04
This SAE Information Report provides basic information about the issues surrounding the administration of stationary, infield sound testing of snowmobiles. The information provided herein is meant to ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-02-26
The scope of this SAE Standard is the definition of the functional, environmental, and life cycle test requirements for electrically operated backup alarm devices primarily intended for use on off-roa...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-02-18
This SAE Standard includes names of major components and parts particular to this type of machine. Illustrations used here are not intended to include all existing commercial machines, or to be exact...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-02-18
This SAE Standard includes names of major components and parts peculiar to this type of machine. Illustrations used here are not intended to include all existing commercial machines or be exactly des...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-02-06
This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multipurpose passenger vehicles. Stamped disc w...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-02-04
To provide a standard vehicle test procedure to evaluate active vehicle systems that takes control from the driver and decelerates the vehicle. These systems shall include but not limited to adaptive ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-02-04
This SAE Recommended Practice encompasses the significant factors which determine the effectiveness of a seat system in limiting spinal injury during vertical impacts between the rider and the snowmob...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-02-04
This SAE Recommended Practice establishes a consistent procedure for measuring and analyzing the natural sway response of a particular trailer when attached to a particular vehicle under specific load...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-02-01
This recommended practice establishes the test procedures, performance requirements, and criteria necessary to evaluate minimum safety and reliability requirements of a childrenThis SAE Recommended Pr...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-01-31
Data from this SAE Recommended Practice permit mapping axle efficiency and/or waste energy over the operating range of trucks, busses, and other highway vehicles based on truck chasses. The procedure...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-01-14
This document is intended to supplement the J1939 documents by offering the J1939 information in a form that can be sorted and searched for easier use.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-01-08
This SAE Recommended Practice provides minimum requirements and performance criteria for devices to prevent runaway snowmobiles due to malfunction of the speed control system.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-01-06
This SAE Standard characterizes grapple skidders and identifies the major components and parts most commonly associated therewith. Illustrations used herein are not intended to include all existing c...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2013-01-03
This SAE Recommended Practice identifies major components and parts peculiar to clam bunk skidders. Illustrations used here are not intended to include all existing machines or to be exactly descript...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-12-17
This SAE Recommended Practice describes the testing procedures required to evaluate the integrity of a ground ambulance-based patient litter, litter retention system, and patient restraint when expose...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-12-17
This SAE Recommended Practice describes the testing procedures required to evaluate the integrity of ground ambulance-based occupant seating and occupant restraint systems for workers and civilians tr...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-11-19
This SAE Standard applies to off-road self-propelled work machines as categorized in SAE J1116. A fast fueling system incorporates a fueling receiver through which fuel is conveyed to the fuel tank...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-10-25
Identification SAE J2461 specifies the recommended practices of a Vehicle Electronics Programming Stations (VEPS) architecture.in a Win32™ environment. This system specification, SAE J2461, was a rev...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-10-24
This standard provides product safety sign artwork and text for hazards common to ready mixed concrete trucks.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-10-17
The purpose of this document is to establish guidelines for determining the critical refrigerant charge for off-road, self-propelled work machines, general purpose industrial, agricultural, forestry, ...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-10-11
The location and operation of instruments and controls herein described are recommended for adoption by manufacturers of trucks and truck-tractors in new or revised designs in order to avoid confusi...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-10-10
This SAE Standard establishes the maximum gradient rating during hopper discharge of self-propelled, driver-operated sweepers and scrubbers as defined by SAE J2130.
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-10-10
This SAE Standard applies to the fuel consumption of non-propulsion engines used to drive exclusively the sweeping and cleaning functions of multi-engine sweepers and scrubbers as defined in SAE J2130...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-10-10
This SAE Standard establishes a method of disclosing the sweep-ability performance of self-propelled sweepers that use broom means for sweeping and collection, together with either a mechanical- or pn...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-10-04
This SAE Recommended Practice identifies the minimum truck tractor electrical power output of the stop lamp and ABS (antilock brake system) circuits measured at the primary SAE J560 tractor trailer in...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-09-24
This SAE Standard covers disposable hydraulic and lube oil filter elements. This document is a general performance specification for filter elements and identifies performance criteria and test method...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-09-18
This SAE Standard establishes a test method and a definition for disclosing the suction air volume performance of self-propelled sweepers that solely use a pneumatic conveyance means for the collectio...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
2012-09-18
This SAE Standard establishes a test method and definition for disclosing the performance of suction/blower fans when applied to self-propelled sweepers that solely use a pneumatic conveyance means fo...
SAE TECHNICAL STANDARDS UNDER DEVELOPMENT
|
Available Standards ProductsResources
General Information |
©2013 SAE International. All Rights Reserved.
